Jump to content
SAU Community

Recommended Posts

  • Replies 70
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

it had a fmic on it and his number plates we 2JZ but i dont know, there was no bov and those things weight a fair bit but it was only on par with v6 commonwhores. We thought he was just a tool who had put badges on and bolted a FMIC in to look "cool"

A mate of mine has a 2JZGTE JZA80, with slicks and NOTHING ELSE DONE TO IT, it ran a 12.7 obviously with lots of practice :) We did have a sneaking suspicion that it came from Japan with highflowed turbos :( made 310rwhp off the boat!

Edited by bubba
Link to comment
https://www.sau.com.au/forums/topic/251396-heyy/page/3/#findComment-4353318
Share on other sites

thank for ur help micheal i got a qoute today for a x force turbo bak zorst for 1450 is that a good and wat sore of power would i get

that is about correct, did it inc the cost of installing the exhaust?

because you already have a cat-back your better off just buying a front pipe and dump pipe as it will be alot cheaper (the cat-back section is the most $$ part of the exhaust)

here are few examples of what you could get and the cost

Stainless Split Dump/Front Pipes - RB20/RB25 - $269.00

jjrexhlogosm.jpg

jjrsplitdumprb.jpg

Product Information

- Manufactured from high grade Stainless Steel pipe

- Stainless Flanges used at both ends (8mm Turbine outlet flange - 6mm Cat flange)

- 2.3mm wall thickness - 3 inch main pipe diameter

- Specially designed moon shaped wastegate divider

- Uninterupted exhaust gas flow through seperate of turbine exhaust and wastegate gases

- Factory 02 sensor screws straight in

- Guaranteed performance

- Guaranteed fitment

- Impeccable weld quality

- 12 month warranty

Link: http://www.skylinesaustralia.com/forums/St...on-t155238.html

Cooling-Pro Intercooler Kits - From $399.00!

cpcoolerkit.jpg

COOLING-PRO INTERCOOLER KIT CONTENTS:

- Cooling-Pro Bar and Plate core, measuring 600 x 300 x 76mm

- Super strength JJR silicon joiners

- Race quality stainless hose clamps

- Mounting brackets, nuts & bolts (Where required)

LINK:http://www.skylinesaustralia.com/forums/Cooling-Pro-Intercooler-K-t138738.html

I just had a quick look and found those 2 items; but there is alot more stuff out their if you take the time to look. most of it can be bought from over-east and will be cheaper than buying it from a shop in W.A.

Link to comment
https://www.sau.com.au/forums/topic/251396-heyy/page/3/#findComment-4353410
Share on other sites

I'm not going down again until the new turbo is on, I only went down last time to benchmark the mph which is why I didn't beat up on it trying to get a perfect launch/better time..

I'm more about going sideways than fast in a straight line heh

Link to comment
https://www.sau.com.au/forums/topic/251396-heyy/page/3/#findComment-4357460
Share on other sites

has not been confirmed yet as getting numbers but i think they said sometime March or that could be when Drift pract at barbs Starts ha.

Will keep you posted :)

next couple of weeks im talin mine down who wants too come down and some time when i lauch it tramps is that normal

Link to comment
https://www.sau.com.au/forums/topic/251396-heyy/page/3/#findComment-4357726
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
    • OK, now we are ready to get started. You need to remove the air boxes on each side for clearance. The cover is straightforward, undo the clips on the top and lift the front cover out of the rest of the housing. If it is tight you can remove the air filters first. The rear section of the airbox is trickier. On each side you need to remove the Air flow meter wiring which is held to the airbox with a clip; you need to get behind the clip on 2 sides if you want to remove it without breaking it - unclip the harder side and pull on the clip with medium force, then unclip the easier side and it should pop out The airbox is held onto the intake hose with a spring clamp; you need to get a flat bladed screwdriver behind the spring on both sides and pop them outwards. When you have got them in the right unclipped place they will stay there and the airbox slips out pretty freely. Put a rag in the intake to prevent anything getting dropped in there, and also to prevent you seeing that the turbo seal is leaking oil (as they do). Then. The top of the radiator is held by a steel plate, it is secured by 2x10mm and 2x12mm headed bolts . Remove them and remove the plate Also grab the bushings that hold the radiator to the plate on each side so they are not lost!
    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
×
×
  • Create New...