Jump to content
SAU Community

Recommended Posts

Hey folks, I did a Brisvegas-Hobart return road trip over chrissy new years. Nothing like the great open road :(

A couple of times when I planted it in 5th gear to pass a car (generally uphill, loaded engine) the check engine light flashed briefly. I'm running a Power FC. Had good fuel in the tank, no more knock than normal (which is pretty much non-existent). Ignition timing is slightly higher than it has been though. It was last tuned about 18 months ago and alls well since then. Got me buggered, is something on the way out perhaps? Something my tuner overlooked? Thoughts appreciated.

Link to comment
https://www.sau.com.au/forums/topic/251474-check-engine-light-rb25/
Share on other sites

Yeah it is. Shouldn't the knock sensor show something when the engine pings? I made a point of watching the gauge when the engine light was flashing, but no noticeably higher readout on the hand-held. The ignition timing has been at or around 10-15 for 18 months, but has jumped up to about 45-50 though. This is a good sign of pinging isn't it?

60+ is definate pinging, thats the only time your engine light will flash. You said you were only seeing next to no pinging which rules that out. The only other thing it could be is reaching the peak of injectors, fuel pump or something else. My guess is Injectors - text book example as you said it was occuring uphill, loaded engine etc.

Why does my engine light flash when I drive with the PowerFC?

The PowerFC uses the factory engine warning light to alert the user of "upper limit" or ceiling values in the engine systems. Things such as airflow meter max value, injector max duty, excessive knock will cause the engine warning to flash. Usually the engine flash is in a sequence of 3 flashes each 0.5 seconds apart. Should you experience this you should review the hand controller max values (press down when in monitor mode and displaying values to see the max values for each) and consult your tuner immediately. Excessively high knock can cause engine damage. Running on max injector duty can also be fatal so speak to your tuner. Aggressive tunes that are tuned around winter temps/airflow and being run hard in summer may cause these symptoms if the tune is very aggressive and on border line of maxing out the stock components. This is only hearsay but I have seen this from at least one or two members.

Taken from http://paulr33.skylinesaustralia.com/docs/...erfc-faq.htm#32

Edited by MintR33

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Impossible to remove the housing while turbo is installed on the manifold on the engine. So I have to do it anyways. I plugged it so there will not be any debris in there. Will vacuum aswell 
    • would a r34 gtr hood line up with gt/gtt stock fenders? after latch, front bumper and hinges are swapped for gtr ones? or would the fenders be too low or high in relation to the hood surface? ( I believe seeing somewhere that gtr front fenders use some type of riser for the sides, but do not know how that relates to stock gt/gtt fenders.)    
    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
×
×
  • Create New...