Jump to content
SAU Community

Ebc's

*Sweetn*

By *Sweetn*,
in Engines & Forced Induction

 Share

Recommended Posts

*Sweetn* Contributor

*Sweetn*

Posted
Posted

hey all im a little bit confused at the moment between electronic boost controllers. i currently have a s1 r33 with a Greddy profec 2 spec B. i am running a pfc ecu without the commander.(is it wasnt there when i bought the car), I am looking between the apexi AVC-R and the Apexi Power Fc boost control kit.. Which is the better of the two and do u need the commander for the PFC boost controller..? any help would be greatly apriecated as i have no idea.. thanks

Link to comment
https://www.sau.com.au/forums/topic/251666-ebcs/
Share on other sites
joeyjoejoejuniorshabadoo Grand Master

joeyjoejoejuniorshabadoo

Posted
Posted

i'm running a blitz DSBC spec s which is basically the same....

i'd stick with what you have and spend the money on a go fast mod :down:

fyi my ebc gets me 20 psi by a titch over 3500 and holds till redline...

Link to comment
https://www.sau.com.au/forums/topic/251666-ebcs/#findComment-4356236
Share on other sites
heller44 Mentor

heller44

Posted
Posted

Is your boost controller working.. ie holding the set boost without deviating too much? If the answer is yes, then why change.. If the answer is no, have you followed the instructions to see if it is just a set up issue? The only other reason I can see to change (if the ebc is actually working) is that you have excess money, I take donations.. :down:

Link to comment
https://www.sau.com.au/forums/topic/251666-ebcs/#findComment-4356303
Share on other sites
heller44 Mentor

heller44

Posted
Posted

I use something a hell of a lot older than what you have.. blitz twin-sbc. not fancy screen, not even a digital readout, just a couple of knobs and a couple of buttons. Holds boost dead flat so who cares what it looks like, or what other fancy features it has. Hidden away in the glovebox as well, better out of sight than ripped off I reckon. Once you have it set you won't want to play with it again. Just read that manual hamish posted up and it looks dead easy.

Link to comment
https://www.sau.com.au/forums/topic/251666-ebcs/#findComment-4356557
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Tomei gasket

      By joshuaho96 · Posted

      I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek · Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...