Jump to content
SAU Community

Walbro Max Pwoer

Dearlove

By Dearlove,
in Engines & Forced Induction

 Share

Recommended Posts

PM-R33 Grand Master

PM-R33

Posted
Posted

Not sure what model it is but my old man runs a Walbro in the Monaro, 370rwkw+ and it holds up fine.

Just run a Nismo/Tomei fuel pump in tank and then if you need more, run an external 044 with the nismo running as a pick up :D

shy_s6 Veteran

shy_s6

Posted
Posted
i used to love the walbro's but after having a spate of them unable to crack 200rwkw latley (last november) i have been sworn against them, 3 were bought from a large victorian speed shop and the other 2 from tweak it (probably all the same batch)

fitting 040's fixed the issue on all 5 cars.

so trent just a single 040 will be fine in a 32 gtr? 350-400rwkw no problem?

abu Grand Master

abu

Posted
Posted

I'm running a genuine WALBRO which is apparently rated at 600hp, currently making over 270rwkw with no fuel issues, getting a retune done this weekend and expecting over 300rwkw so will see how it holds up

If it fails or starves then 044 without a doubt

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • r32-25t
      R32 gtr transmission strength, billet plate

      By r32-25t · Posted

      Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...