Jump to content
SAU Community

Recommended Posts

hey guys

i need help! was driving the other day and my girlfriend told me that there was somthing dripping on her foot on the passenger side footwell of my 33 GTS-T

A closer inspection found that it was coolant. i checked the radiator, had no pressure in it when hot and the level had dropped considerably

can someone please give me some info on the cause. i have a feeling that its the heater core but im not sure

also on that note, where is the heater core located on this model and how do i get it out?

cheers

Link to comment
https://www.sau.com.au/forums/topic/252141-r33-gts-t-heater/
Share on other sites

hey guys

i need help! was driving the other day and my girlfriend told me that there was somthing dripping on her foot on the passenger side footwell of my 33 GTS-T

A closer inspection found that it was coolant. i checked the radiator, had no pressure in it when hot and the level had dropped considerably

can someone please give me some info on the cause. i have a feeling that its the heater core but im not sure

also on that note, where is the heater core located on this model and how do i get it out?

cheers

hi mate your heater core is behind the dash inside the car ,and it is a shi...t job to change it ..mine done the same thing ..all i done was pull the 2 hoses off that run to the heater which you will find in the engine bay ..just pull them off and either join them together .or put bungs in them so water doesnt get to the heater core .just means you wont have a heater ...thats the easy fand cheap fix ..

Yep, almost positive it's your heater core, it's a common problem. If you do a search there is a tutorial on how to remove the heater core, it's a prick of a job, but can be done in a day. Problem is finding a 2nd hand replacement core, or putting up with no heating :(

ah k then

cheers for the help guys

might have to join the pipes in that case coz it sounds liek a crap job:(

and im guessing a new core would be fairly expensive to

It's easy enough to bypass, but that will still leave a fair bit of water in the core already, and you want to be careful it doesn't lead to ruting your passenger footwell.

Yep

http://www.skylinesaustralia.com/forums/He...WTO-t32611.html

Apparently a replacement heater core isn't that expensive

I got a replacement from my local natrad dealer ( www.natrad.com.au ) for 225, it was the 300zx heater core - I had to take mine out, show him it, then he measured it up and figured out it was the 300zx one.
Be aware that if you bypass the heater and if you get a yellow sticker, that will be one of the things the inspector will make you fix.

thats one reason why you just pull the hoses off ,and put bungs in them so water cant get in the heater core but still looks like its hooked up .and that solvex that problem unless they check it .

If you block them off then the water cant flow like the system was designed. I would much rather loop them and keep the system working as was intended.

I think it would be defectable if the inspector was a c**t as you wouldnt be able to defrost your windscreen on cold mornings.

I have replaced one before and it wasnt that bad of a job. Keep in mind I had taken a dash out before so a lot of it wasnt new to me. Also I used an R32 heater core and it fit in the R33 just fine....which might open up your second hand market a bit

mmm yea i will join them and keep it flowing:)

ah right that sounds good

i like cheaper things lol

i wonder though...... might be a bit hit and miss with second hand whether its going to have the same problem or not?

Yeah but I would rather replace 2-3 second hand ones than pay the price nissan would want for a new one. That said, I have never got a quote from them so it might be worth calling just for a laugh.

You may even have some luck taking the old core out and bringing it to a radiator service center to get it rebuilt/re sealed

Yeah but I would rather replace 2-3 second hand ones than pay the price nissan would want for a new one. That said, I have never got a quote from them so it might be worth calling just for a laugh.

You may even have some luck taking the old core out and bringing it to a radiator service center to get it rebuilt/re sealed

haha think id rather pay the extra whatever it is than pull my dash out 4 times lol

doesnt look like much fun from the drawings and tutorials and stuff

mmmm ye thats an idea ay

should look into it

lol yes and my cruiser has gone 3 years with no heater as well :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...