Jump to content
SAU Community

Recommended Posts

I'm sorry if this question has been asked before i couldn't find the answer any where, please send me a link if there is!

My question is will i get picked up by cops if i put pod filter on my skyline, I am a p plater in Queensland i have heard that it counts as a modification and if a cop had a bad day it could be a reasonably excuse to give you a hard time, i am just curious if this is true, is it illegal to mount a pod filter in your car?

Link to comment
https://www.sau.com.au/forums/topic/252335-pod-filter/
Share on other sites

shouldn't be illegal but im sure if they wanted to they would pick something with it - easier to just box it then you have no problems with cops or heat from the engine

but really why do you want a pod i would just keep the airbox and get a high flow panel - i would of preferred to keep my box but with my FMIC i had to remove it

Link to comment
https://www.sau.com.au/forums/topic/252335-pod-filter/#findComment-4364525
Share on other sites

i got pulled over twice in like 5 minutes at the spit the other week and both cops looked under the hood and they didnt say much about my pod i asked about them and was told that they only have to bolted in but he said some cops think otherwise and if they want they can book you for not having them boxed in

Link to comment
https://www.sau.com.au/forums/topic/252335-pod-filter/#findComment-4374606
Share on other sites

The last time I checked it's fine to have a Pod filter setup in QLD if the following requirements are met:

  • It's a dry filter element (K&N are oiled therefore illegal)
  • The Pod must be secured

Link to comment
https://www.sau.com.au/forums/topic/252335-pod-filter/#findComment-4374696
Share on other sites

Yep call em, They are legal, must be secured properly, be of flame retarding materials, & non oiled-which nissan usually require from air filters anyhow-and oiled filters fowl the A/F meter sensor anyway.

Qld police can interpret as an induction system that may need to be enclosed due to induction noise issues- up to officer at the time of roadside inspection.

Not sure on the P-Plater issue tho

Link to comment
https://www.sau.com.au/forums/topic/252335-pod-filter/#findComment-4374803
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...