Jump to content
SAU Community

Recommended Posts

Item: 180sx

Location: rocky

Website: here

Item Condition: fair

Reason for Selling:kid on the way

Price and Payment Conditions: 18grand or swap for tuff 4door. swap is what i would rather do

Extra Info: front bar and guards need replacing/ repairing

Pictures:

Contact Details: pm me or post here. or email me or add me at [email protected]

wheels /suspension

advan racing 17x9 and 17x8 tri spoke wheels

255's rear 235s front getting close to be replaced

5mm front spacer 25mm rear bolt on spacer

billet 5 stud hubs front and rear from just jap

r32 rotors /calippers front std rear

hot bits coilovers

jic caster rods

aluminium cradle lockers

body/paint

ford envy green with extra gold pearls

including engine bay and rocker cover

30mm wide rear 25 mm wider fronts

full uras bodykit and clear lights to suit

gearbox/ clutch

os giken twin plate clutch.

os giken 1st 2nd 3rd hardened gearset

engine/ turbo

greddy sump

eagle rods

aries pistons

fully balanced bottom end including clutch

arp head/main stud kit

arc race bearing

reseated valves

new exhaust valve guides

all new seals through engine

jun high rev valve springs

jun 264 11.5mm lift in/ex cams

tomei rocker stopper kit

increased presure oil pump

walbro fuel pump

malpasi fuel presure reg

tomei 555 injectors

stainless low mount manifold

garett gt2530 4inch infeed rated at 440hp

gktech exhaust

4 inch intake pipe into standard position for airfilter

hks airfilter

hybrid intercooler kit modified hotside

gfb blow off valve "bovus maximus"

earls oil cooler and filter relocater kit(not on car)

twin electric thermo fans

interior/electrics

apexi avcr boost controller mounted to climate controls hole, controls removed

apexi power fc d jetro series

apexi pen turbo timer

splitfire boost guage

autometer oil pressure and water temp guages mounted in centre airvent in custom mount

kenwood head unit kenwood 6 inch speakers in front

power cable and rca's running to boot

sports steering wheel

bride drivers seat

post-28319-1233319606_thumb.jpg

post-28319-1233319687_thumb.jpg

post-28319-1233319795_thumb.jpg

post-28319-1233319831_thumb.jpg

post-28319-1233319844_thumb.jpg

post-28319-1233319869_thumb.jpg

post-28319-1233319899_thumb.jpg

Edited by yogi_in_a_180
Link to comment
https://www.sau.com.au/forums/topic/254881-180sx-sr20det-sell-or-swap/
Share on other sites

whats wrong with the front guards and bar??

guards are both split and bar is chipped

also all tyres recently replaced

new coil packs, the red ones lol

gk tech stainless exhaust

Edited by yogi_in_a_180

What ECU,

do you have power figures?

how much boost, when was the engine built and who by....

can u put up photos of the damage?

Edited by axe s
What ECU,

do you have power figures?

how much boost, when was the engine built and who by....

can u put up photos of the damage?

power fc d jetro the one with a map sensor

12psi atm

engine built bout 15,000 klms ago by myself

never had a full power tune only but was dyno tuned to run without leaning out made bout 260hp

will try get pics of it soon gotta charge digi cam batts

pics of anything else?

Edited by yogi_in_a_180

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...