Jump to content
SAU Community

Recommended Posts

Is it for S1 or S2 R33?

how do i tell...PaulR33 ??

EDIT: just found out it doesn't matter...but as its a brand newie id say its for a series 2. But either will work in either.

Edited by DiRTgarage
how do i tell...PaulR33 ??

EDIT: just found out it doesn't matter...but as its a brand newie id say its for a series 2. But either will work in either.

Yes, will work in both series 1 and 2

Look all the wankers PMing with low-ball offers...its this simple...

THIS IS A GENUINE AUSTRALIAN PRODUCT FROM ACCESS AUTOWORKS...NOT A CHEAP IMPORT AND IS ALMOST $500 LESS THAN COST !!! HOW MUCH MORE OF A DISCOUNT DO YOU THINK YOU ARE COMFORTABLE RIPPING OUT OF MY WALLET?

COMES WITH FULL SUPPORT AND PART WARANTY.

see look...

http://www.accessauto.com.au/Items/ap-414-...GTS-T%20RB25DET

They are $2200 from Greenline and are no longer available from Nengun...$1500 is an absolute bargain.

Edited by DiRTgarage
cheap power fc's are a thing of the past since our $ went up to shit.

Unfortunately everyone now wants a Vi-PEC...making the Power FC even harder to sell.

Might have too keep it and show my grankids what we used to put in our cars...they will say "omg solid state technology used to run your cars...gee grandad you are old"

Edited by DiRTgarage
Look all the wankers PMing with low-ball offers...its this simple...

im pretty sure i sent you a pm asking if u can send to adelaide, and at the same time asked for bank account details so i could put in the full amount you were asking in!!!!

you had your sale right there... you lost your sale right here, i dont think i will buying from you now

i dont intend on being a keyboard warrior :D but your sale tactics fail

im pretty sure i sent you a pm asking if u can send to adelaide, and at the same time asked for bank account details so i could put in the full amount you were asking in!!!!

you had your sale right there... you lost your sale right here, i dont think i will buying from you now

i dont intend on being a keyboard warrior :D but your sale tactics fail

You actually said this...

ok, let me do a bit more research into it. as it'll be going into R32 rb25det there's a few thing im unsure of.

to be fair i thought id wait till i heard "yes i definately want it from you" before forwarding any of my details.

If you thought i was putting you in with all the "ill give you $800-$1200" people you were wrong, very wrong. You were one of the only people trying not to squeeze as much off it as you could...much appreciated trading. But getting my PM box hammered everyday by low ballers is a little frustrating.

no big deal...no 'sale tactics' here mate...ill put it on the shelf till someone genuine comes along.

Edited by DiRTgarage

Hey there

Just tryed sending a message but ur inbox is full. I am very interested, i have a local source stating a similar price i believe which i am checking tommorow. I really am after one without the hand controller but if i cant find anything tommorow then I shall shall send a confirmation either tommorow night or tuesday morning, unless you sell it before then of course. But key me in for definately interested (And not argueing on price :D ).

Cheers. Luke

hey mate sent you a pm the other day about the z32 afm, havent got a reply from you but basically im just wondering if you still have it and if it comes with a plug too coz im keen to take it off your hands

cheers dale

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...