Jump to content
SAU Community

Recommended Posts

Hi i am selling a full turbo kit to suit r33 or rb25 Kit Done less than 1500kms Includes:

600hp Genuine Garrett GT35R ball bearing turbo .82 Exhaust Housing

Top Mount Manifold

PSR Wastgate

Custom V-Band Dump pipe with custom wastegate plate plumbed into Dumpipe

Oil and Water Lines

And Intake Pipe with Apexi power Intake Air Filter

Setup good for over 350rwkw everything included basically bolt in.

Cost me over $4000

looking for $2700ono

Must Sell ASAP. Will post

Link to comment
https://www.sau.com.au/forums/topic/255319-full-gt35r-turbo-kit-suit-rb25/
Share on other sites

willing to separate oil/water lines n intake pipe?
Would prefer to sell the whole kit unless i find buyer that wants the turbo and wastegate without them. Then i will seperate. sorry

I dont want oil/water lines and intake pipe.

I will offer you $2000 for the rest.

EDIT:

That manifold looks stainless, is it? if its a chineese stainless its worth like $50 as they warp really bad.

I have one that is that badly warped if you put it on a flat surface each end of the manifold is lifted like 1cm. it was on the car for about 30min of driving.

Edited by Finny

I purchased the manifold from jpc they had a spare one there, I used this manifold with my last turbo setup which was on for 2 years and i have never had a problem with it. Only had the 3540 on for less than 3 weeks, and was running fine. Spent alot on the wastegate and no expense spared on my engine and turbo setup. I will let you know later on tomorrow if i dont sell the whole kit and we will work something out. cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
×
×
  • Create New...