Jump to content
SAU Community

Recommended Posts

Alright, so i dumped the oil from my gearbox the other day and filled her back up with the correct amount of oil through "THE GEARBOX LEAVER" thinking that this gearbox would work the same way as any other gearbox i have serviced. Anyway so i out it back together and start driving home, by the time i got there there was oil all the way down underneath my car and on my exhaust. Found the problem being the gearbox leaver boot, so i replaced that and topped it back up with oil, this time through the top lug on the side of the gearbox, this was more of a quick job so i found the best oil i could for a midnight on Tuesday and put her in(happened to be multitrax).

I wasnt to happy with this oil so i bought some new stuff today and replaced it again through the leaver, problem is when i go to check the level from under the car i cant get it, and the oil seems to be sitting in a gallery on the top part of the gearbox, or the transfer case.

For though who know rb26dett gearbox's you will realise they have a chain system and a oil pump inside of them, my question and i couldn't find the answer through all the reading i have done, is the main gearbox and the transfer case connected and run the same oil? or are they different galleries? I really need some help on this! my car is sitting up on jacks.. sad.gif

cheers jake.

Link to comment
https://www.sau.com.au/forums/topic/257186-r32-gtr-gearbox-problems/
Share on other sites

is the main gearbox and the transfer case connected and run the same oil?

No (in terms of oil usage) and no.

The transfer case uses ATF and the gearbox uses.....gearbox oil. The shift lever bolts to and connects inside the transfer case in the GTR gearbox. So when you filled the 'gearbox' through the shift lever hole, you actually only filled the transfer case....and it would have been waaaaaaay overfilled, thus the cause of the leaks, not to mention using the wrong oil.

In fact, the filler plug for the gearbox is on it's side, accessed from the underneath the car. For the transfer case, the filler plug is at the back of the case and also accessed from below.

Suggest you get hold of a workshop manual.

Edited by SteveL

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...