Jump to content
SAU Community

Recommended Posts

Hi guys,

In search of a new fuel pump.

Looking at a Bosch 040 fuel pump? Will that be ok?

I hear lots of people going the Bosch 044 fuel pump?

Whats the difference and which one should i go?

I got an Rb20det with minimal mods, think the fuel pump is in it's last legs.

All advice is apprectiated!

Link to comment
https://www.sau.com.au/forums/topic/258378-fuel-pump/
Share on other sites

Any of the Bosch in-tank pumps will be fine if you have minimal mods. The 044 is an external mount, so not really the best option. The 040 would be my choice of the Bosch's, or the Walbro 255LPH pump

http://boschfuelpumps.com/

Cheers for the advice.

You confirmed my initial thoughts.

Link to comment
https://www.sau.com.au/forums/topic/258378-fuel-pump/#findComment-4442402
Share on other sites

Personally, I would go the 044 pump over the 040 (and GTR, why put a 2nd hand fuel pump in?).

I'm running an 044 internally and my mate is running an 044 internally (and his car is making 530awhp from one internally mounted 044).

The 040 is more of a direct swap but it has an integral pickup/filter (meaning that it draws from the bottom face of the pump through a screen).

The 044 requires a little modification of the bracket to hold it on and because it has a fitting on the end you can use a stock-like sock-filter setup.

Whichever way you go, you should be rewiring the pump for a constant 12v as opposed to variable voltage.

I cbf putting my fuel pump in (it's like the only thing I paid someone to do to my car other than tuning and alignments), 044 pump cost me $215 new off ebay and I paid Hyperdrive ~$220 to install the 044, they supplied all the fittings & filter and rewired for 12v and a better earth.

Link to comment
https://www.sau.com.au/forums/topic/258378-fuel-pump/#findComment-4443192
Share on other sites

Why put a 2nd hand pump in? .. Because it's more than capable.

There's no need to put a 500hp fuel pump in a car with less than half that... You could spend $200 + on a pump, but a $50 one will be just as good... and it's an easy install.

There's plenty of GTR's out there who have replaced their pumps because they are chasing big power numbers, and if you've got a lightly modded rb20, then the GTR's old pump is a great mod.

But hey, if money isn't an issue for you then go all out.

Link to comment
https://www.sau.com.au/forums/topic/258378-fuel-pump/#findComment-4443464
Share on other sites

It may be more than capable but I wouldn't trust a 2nd hand fuel pump. If that ~20yo pump decides it wants to die at the wrong time, goodbye engine.

For a bit over $200 and some time/patience or another $200 for a pro install, put a decent pump in there.

If you can't afford a $200 fuel pump.. you shouldn't be modifying cars :)

But hey, at the end of the day, it's not my engine.. so go for it ;)

Edited by bubba
Link to comment
https://www.sau.com.au/forums/topic/258378-fuel-pump/#findComment-4444333
Share on other sites

Work out whats cheaper .. new pump or new engine

if you only have minimal mods then you could pick up a 2nd hand GTR pump pretty cheap and it'd be more then enough. Plenty of 32s are using them (check out the rb20 power figure registry in the forced induction section)
my mate is running an 044 internally (and his car is making 530awhp from one internally mounted 044).

We have same set up with 31 making 418rwhp , better fuel system will go in before we hit 500hp

Link to comment
https://www.sau.com.au/forums/topic/258378-fuel-pump/#findComment-4444574
Share on other sites

We have same set up with 31 making 418rwhp , better fuel system will go in before we hit 500hp

Better how? use the intank 044 as a lift pump into a surge tank then twin 044's?

I was a bit sceptical when matey said he was going to run a single intank 044 with his power level but it's coping quite well!

Link to comment
https://www.sau.com.au/forums/topic/258378-fuel-pump/#findComment-4444641
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...