Jump to content
SAU Community

Recommended Posts

Hey people just having a clean out of everything iv gathered over the years:

Ive bought a fair bit of this stuff recently in hopes of building a track car but i just dont have the time or money anymore:

-RB20 MOTOR WITH EXTREME (1100KG OR 1200?) 6 PUK CLUTCH (has just had new timing belt, water pump, sump gasket, oil pump gasket, front and rear crank seals, spark plugs. All big end and main bearings inspected and look as new) - $1200

Bought motor off a mate 5 months ago, he got it from D1 from a front cut with 60,000 on it. He used it for a year so motor has done 80-90,000kms.

The clutch he put on it cost him around $800-900

the motor comes with the standard turbo, upgraded AFM, wiring loom but is missing coilpacks, ECU and a couple of sensors.

-R32 COMPLETE REAR END (includes cradle, diff, axles, hubs, brakes, hicas rack & rods) - $550

-R32 ENGINE CROSSMEMBER - $130

-R32 FRONT HUBS (NO BRAKES) - $100 SOLD

-R32 STEERING BOX, RACK AND TIE RODS - $200

-R32 UPPER CONTROL ARMS - $70 PAIR

-R32 SWAY BAR - $60

-STANDARD SUSPENSION (FRONT) - $50 PAIR (X2)

-POWER STEERING PUMP - $30ea (X2)

-HICAS LOCK BAR - $100 (paid 150 for it new and it was used for 1 track day)

-FRONT STRUT BRACE (nismo) - $100

-ALTENATOR - $30 SOLD

-R32 CLUTCH SLAVE CYLINDER - $50

-STARTER MOTOR - $30 SOLD

-STANDARD BLACK FRONT BAR - $30

-FIBERGLASS GTR FRONT BAR IN GREY PRIMER - HAS SOME DAMAGE, MINOR REPAIRS NEEDED - $100 (paid 400 for it new)

-LHS TAIL LIGHT AND SURROUND - $20 (some plastic clips snapped off - super glue job)

-16" 5 STUD SPEEDY LONGCHAMP WHEELS - $300 (NO TYRES)

if you want any pics let me know.

my number is 0433 570 412

located in adelaide

cheers.

Doug.

post-26585-1235975014_thumb.jpg

post-26585-1235975027_thumb.jpg

post-26585-1235975055_thumb.jpg

post-26585-1235975068_thumb.jpg

keen as on the wheels and gtr front far, how much shipped to melb ?

does it come with a reo bar ?

and would you have a right hand side headlight ?

Edited by hirsty
  • 2 weeks later...

PRICE DROP ON MOTOR - $1000 (i am losing money on this motor and i just want it gone)

Diff is sold, all other rear end parts still for sale:

-R32 REAR HUBS AND BRAKES (calipers, rotors, pads (80%), brake lines, h/brake cable - $250

-R32 REAR CRADLE - $100

-5 BOLT HALF SHAFTS - $90

-R32 REAR SWAY BAR - $50

-R32 HICAS RACK AND RODS - $30

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...