Jump to content
SAU Community

Recovering Race Seats

Noddy

By Noddy,
in Motorsport Discussion & Builds

 Share

Recommended Posts

Noddy Proficient

Noddy

Posted
Posted

As some of you might know, this is my trade. Even though I have changed professions i still do some work on weekends.

I have been trimming some historic racecars lately and thought u guys might like to see what goes into a basic race seat. These are new seats that are built to a weight so no extras that might weigh anything goes in. The seat rtimmed in the pic is a drivers seat and is heavier than a passenger seat. In the Historic class they have to have a passenger seat that looks the same, and they do, but havn't been made with the intention for any1 to sit in. Did I mention wieght? I remember 1 day when Matt was beaming ear to ear proclaming to have found 65grams hiding in an integral part of the engine.

Anyway, to start with you will will need an open space to work in with something on the work surface so the gelcoat/paint doesn't get scratched up.

02032009_005.jpg

then a shell that needs trimming

02032009_001.jpg

02032009_002.jpg

02032009_003.jpg

02032009_004.jpg

Some padding cut to the shape of the seat

02032009_006.jpg

Spray some contact glue on it

02032009_007.jpg

And in the shell

02032009_008.jpg

Just flop the foam in the shell...

02032009_009.jpg

...and trim it up.

02032009_010.jpg

I do a few of these so I have made some patterns for the fabric.

02032009_011.jpg

mark out and cut out the material

02032009_012.jpg

Sew the quilting in all the parts together.

02032009_014.jpg

Now you just need to glue both parts, flop it in the shell, secure all the edges and trim it all up neatly.

02032009_016.jpg

trim up the seat belt holes so the raw edges are neatly hidden.

03032009.jpg

and last of all you will need to make up a cusion that matches, and fit it of course so it wont slip out unterbrakes.

03032009_001.jpg

last of all it needs to be dropped off so the guys can put it in the #7 car. Yes the all have my interiors in them, and this is the last seat.... YAY! Job done.

03032009_002.jpg

Link to comment
https://www.sau.com.au/forums/topic/259394-recovering-race-seats/
Share on other sites
Beer Baron Grand Master

Beer Baron

Posted
Posted

GTR seats are a bit different though to fibreglass race seats as they are just a wire frame wrapped in foam then trimmed. would be much more $$$ and the hard bit is getting fabric to match the passenger seat and door trims etc. the only easy way to cure them is buy a generally less worn passenger seat and use the fabric off that. still not easy though.

Noddy Proficient

Noddy

Posted
  • Author
Posted

I didnt intend for this to go this way but I have found a very good match for GTR seats. And as you say, new material does stand-out somewhat. The biggest headache with skyline seats in general is that the cover is glued on. Normaly there is a short sock on the inside with a spring/hardened wire insert that is clipped to another wire set into the foam. Gluing the cover on makes them a real pain in the botbot. And yes the price is much higher if not for the extra time spent but the AGRO tax that goes with it.

As a side note if you are serious about getting a seat covered, pm me. Might take a while though, it is realy only a hobby these days to help fund my own racing.

No the Astra does not have 1 of my race interiors in it. It was just in the way this morning. It's not often most of the RX2's are all together like that. Just made a good snapshot.

Rhys9 Enthusiast

Rhys9

Posted
Posted

Stuart i've been meaning to come round get you to look at the Recaro's in my GTR, and generally say hi.

Sorry to hear about how the new manifold and throttles went, what you reckon manifold leak, or flow problem??

Rhys

  • 4 weeks later...
warps Mentor

warps

Posted
Posted
last of all it needs to be dropped off so the guys can put it in the #7 car. Yes the all have my interiors in them, and this is the last seat.... YAY! Job done.

03032009_002.jpg

My god, look at all those RX2's :):cheers:

Good to see them put to good use, not just sik maccas cruisers or 9 second 13BT street sleepers

Neil Grand Master

Neil

Posted
Posted

Ah,,,don't you all love a garage full of rotors. Come on,,,after a Skyline,,,what other tin-top would you own.

I'd like my Radicals seat done mate,,,pm me if you are interested. Yes it's full fibreglass.

Toyota's by the way are for poofs.

Neil.

Noddy Proficient

Noddy

Posted
  • Author
Posted

depending on the materials you chose and embroidery, I shouldn't think it would be much if any more than the $300ish mark for a normal Vello seat. the wrap around seats will be abit more in materials and to be honest there a bit of a pain in the butt.

Niel, PM sent.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • myrbgivesmeheadaches
      RB25DET NEO Cylinder Head

      By myrbgivesmeheadaches · Posted

      Did this end up working? Did you take some pictures?
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...