Jump to content
SAU Community

Recommended Posts

  • Replies 89
  • Created
  • Last Reply

Top Posters In This Topic

omg so buggered!!!!!!!!!!!!!

Firstly well done to Chubbs n Clapa achieving their goals. Chubbs proving that even hairdressers are fast and can steer with 54.9, Clapa steering the tug boat around in an impressive 53.6 and George (Demon) getting his EVO out for the first time punching out a 58.5!!!!

Now the failvia... well it seems that this mysterious issue is not so evident anymore... still some vibration under heavy brakes but i think that is just the pad/rotor... anyways it ended up getting around in a 51.7 which was happy about. Goal for sunday with all the stars and moons aligned i will get into the 50's....

A good alignment done and get the tyre pressures right she will be good to roll...

A big shout out to JB again for the day, Ben harper and george medeike (spelling lol) showing me how the car should be driven :whistling:

So what else is left to do.?!?!?!?!!?

Of course.. BBBEEEEEEEEERRRR!!!!

Its Ben Porter :D:whistling:

Yeah, what an epic day, plenty good cars, loads of track time, I love the south circuit!

the mx5 was keeping most of the cars honest! loved it!

Thanks to JB for today, totally worth every cent, I learnt so much, if it werent for these guys, Id be alot slower as I wouldnt have a clue how to drive this new thing properly!

Big ups to Eugene, George, Ando and Clappa also for doing great times and enjoying the day!

Now, my goal is 53's for sundays supersprint!

Sorry to hear all the bad luck Stu :D

What pressures do u need to run Ando and what have you been running?

At that Wakefield day (first time on semi slicks) I was running 30psi cold which rose to about 32-33psi hot but found out from the Yokohama dealer just near me that I should have started them at 25psi cold which will rise to 26-27psi.

Doubt I would have noticed any difference on my first day out in the car but ill give it a go at the OP GP day.

Ben - Champ i only adjusted the temp once all day lol.... i put 26 psi cold all round first session and came in with 33psi on drivers front & rear and 30 psi passanger front and rear so obvisouly there is a heap more load on the right hand side of car.... but yeah that was it for all day... just left them as that hahahahahaha just couldnt be arse fiddling as we had no air compressor, except clapas little cigarette lighter jobby which had less huff thana 70yr old hooker!!! :D

My moto if it goes, drive it.... meh to finer technical details... thats for this Sunday @ supersprint :( Today was R&D...

post-263-1242210723_thumb.jpg

Huh what a day. Chris you shoul dhave the pic with headlights out...hehehehe. All was perfect with no events registered. PERFECT PRERFECT PERFECT.

Ian you are an inspiration mate, when I grow up I wanna be like you ...heheheheheh

Eug

LOL

Sounds like Eug has a crush on ando!

dont blame him though :D

Who took the other shot spando??

LOL, my car looks like a toy car in the one clappa took!

and for the record, I AM in front of that WRX :( (not he is catching me! :( )

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...