Jump to content
SAU Community

Recommended Posts

NISSAN SKYLINE R33 GTS-T S1 M-SPEC

ENGINE:

RB26DETT conversion

RB26 sump w/transfer case sliced off

RB25 engine mounts

RB25 Harmonic balancer

HKS Intercooler

BLITZ front pipes

SIGNAL straight through carbon muffler

HKS Pod filters

Splitfire coil packs

TODA Racing clutch

TODA Racing 4.5kg Flywheel

CUSCO 2 way mech diff

IRIDIUM Plugs - 6's

R33 GTR fuel pump

SUSPENSION / BRAKING AND HANDLING:

SELBY rear 28mm sway bar

RACING GEAR coilovers

D1 rear camber arms

D1 HICAS lock

CUSCO front tension rod

Solid rear subframe bushes

D1 adj castor rods

PROJECT MU Slotted front rotors

TRW (LUCAS) brake pads all round

NISMO Front strut brace with brake stopper

GTR rear strut brace

BODYWORK & INTERIOR

Full body respray in Blood Orange

Satin Black bonnet and wing

SPARCO bonnet pins

NARDI Steering wheel

TRUST gear knob

SPARCO Spirnt drivers seat w/ BRIDE Rail

GReddy Profec B Spec II boost control

GReddy Turbo Timer

New Carpet

GReddy Boost Gauge

engine has spun a bearing , have R33 GTR Bearings to go on the engine

also have R33 GTR Crank that has been linished and polished with oil galleries filled with grub screws

R33 GTR Pistons & Rods

R33 GTR Oil Pump (Rebuilt)

Possibley interested in trades

Price $14,000 ono

bhmqt.jpg

would have more pics but GPU in my pc has died so i cant access the hard drives for now.

Link to comment
https://www.sau.com.au/forums/topic/260151-my-r33/
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...