Jump to content
SAU Community

Recommended Posts

hey guys.. i have a r33 GTS-T 94 modle. I am having problems with the breaks the front break pad keep squeeling and i had my disces machined and had 3 lots of new pad put in.. still they squeel.. now when the break place pulled the break pads out they are shines each time.. any ideas why this is happening..

Link to comment
https://www.sau.com.au/forums/topic/260298-break-pads/
Share on other sites

BRAKES ffs!

Did you bed the pads in correctly? Are the anti-SQEAL shims behind the pads?

i got a new set of pad put into but i am sic of goin bak to the place get them changed.. but on the way home they started to squeel kinda again and not happy :D i was told to bed them u have to get to like to 80 then break fairly hard... and for th anti-SQEAL shims i couldn't tell ya sry..

Link to comment
https://www.sau.com.au/forums/topic/260298-break-pads/#findComment-4467053
Share on other sites

heres some instructions for ya, and remember, DO NOT come to a complete stop... you can stuff your pads, probably the reason why you had to go back 3 times.

BEDDING IN INSTRUCTIONS

1. Install disc pads and check fit.

2. Pump brake pedal until pedal is hard.

3. Perform 2 stops from 50Kph to 20Kph with medium pedal effort.

4. Perform 6 stops from 110Kph to 70Kph with high pedal effort.

5. Drive vehicle for 10-15 minutes at 70 to 100Kph without using the brakes to allow them to cool

6. Park vehicle and allow brakes to cool to ambient temperature.

DO NOT STOP VEHICLE WHEN PADS ARE HOT DURING BEDDING.

THIS WILL SEPARATE THE PAD FORM THE BACKING PLATE

Bedding should not be performed until disc rotor has been bedded.

The disc pads will smoke and smell whilst bedding.

Link to comment
https://www.sau.com.au/forums/topic/260298-break-pads/#findComment-4470180
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...