Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

BUGGA!

Went for the tune today and made 255awkw... I wonder whats the difference between rwkw and awkw... =(

But the car feels soooo much smoother now.

BUGGA!

Went for the tune today and made 255awkw... I wonder whats the difference between rwkw and awkw... =(

But the car feels soooo much smoother now.

It’s around a 15% driveline loss.

So say 255awkw + 15% loss (38kw) = 293rwkw = 392rwhp

Which is about right for a standard N1.

@super coach tristan: tried a new grip tonight and got 51 with a strike rate of ~210 :blink:

Also got about 2 dozen stumpings and catches behind the stumps and a few wickets bowling. Good night (y)

To break it down more, rwkw to flywheel kw is roughly x1.33

so, 293rwkw x 1.33 = 389FLYWHEEL KW

Both post's above are rough, everyone has different veiws on loss and conversion rates

Maybe all these while the 300kw I had in mind was rw not aw. But the fact that the car feels lighter/smoother really surprises me. 1st gear used to hit limiter at 60-70km/h now it goes up to 80+. Amazed.

A stock N1 will never make 300awkw, unless the dyno is happy, or you tell the tuner to input 300awkw on the graph lol.

Your car is very healthy and is on par - What else is done to it?

BUGGA!

Went for the tune today and made 255awkw... I wonder whats the difference between rwkw and awkw... =(

But the car feels soooo much smoother now.

Wooooo good shit

Ok, the list is as below

1) Trust Ti-R exhaust

2) HKS Front Pipe

3) Apexi Power FC

4) Apexi Boost Controller Kit

Thats all. Everything else is stock. 1.15bar I think (on the pfc hc). Cant get it to hold 1.2bar. No engine mods. Injectors are max at 90%.

Glad to hear the tune is good Brandon, who tuned it for you?

They must have lifted the rev limit a bit :blink:

Gavin Woods @ Autotech. Shit loads of GTRs... oh and 1 Tommy Kaira 32 (dont know real or not)

Ok, the list is as below

1) Trust Ti-R exhaust

2) HKS Front Pipe

3) Apexi Power FC

4) Apexi Boost Controller Kit

Thats all. Everything else is stock. 1.15bar I think (on the pfc hc). Cant get it to hold 1.2bar. No engine mods. Injectors are max at 90%.

Sort out why it's not holding more boost

- Get a better fuel pump

- Throw in some larger injectors

- Get a good set of cam gears

Spend more time on tuning and you will have a friggin quick car..

Your lack of boost.. They're N1's even 1.2bar is tame... and lack of fuel is why you only got 255awkw. IMHO, with the above and a very good tune you should get up around 280awkw, if you run more than 1.2bar..

If I'm ever gonna get it tuned again, I'll try Matt Spry.

Both Gavin and Matt gave me a good impression when I called comparing to the others.

Sort out why it's not holding more boost

- Get a better fuel pump

- Throw in some larger injectors

- Get a good set of cam gears

Spend more time on tuning and you will have a friggin quick car..

Your lack of boost.. They're N1's even 1.2bar is tame... and lack of fuel is why you only got 255awkw. IMHO, with the above and a very good tune you should get up around 280awkw, if you run more than 1.2bar..

He reckon its restriction. Or maybe injectors (he's not comfortable running higher than 90%). Or might be the boost controller (I've heard the kit doest hold boost very well after 20psi)

If I'm ever gonna get it tuned again, I'll try Matt Spry.

Both Gavin and Matt gave me a good impression when I called comparing to the others.

Don’t get me wrong, Gavin knows more about Nissans than most people – however to cut a VERY long story short, I bought a second hand Q45 throttle body from a wrecker, unknown to me at the time the wrecker swapped the TPS unit for a ca18 unit, which meant the car wasn’t tunable… My car was with Gavin for a full day and he couldn’t find what was wrong with it.

I took it to Matty and he found within 5 minutes that the TPS had been swapped over, we put the correct Q45 TPS in and had it tuned…

I know where I will continue to keep going back

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Resizing injectors in Nistune can be done a couple of ways, and there are a couple of ways that you can make a mess of it. The tuner needs to be really aware of the effects of whichever approach he uses (either K, or TIM). They are both easy enough to "get the injector size right" to run the engine. But little details like old start enrichment and hot start are affected differently, depending on which boxes you check.
    • Pretty safe to say almost everyone that has tuned their own car has experienced this issue. The difference being that we have our laptop in the car and when it happens, it's literally 10 seconds of tuning to sort it.  Would you be happy to plug in your laptop and sort this yourself? It is a very simple process and there is no risk of harming your engine (if you are worried about that). 
    • Yeah thats the next step now, either they wil or i will take out for a drive to work and go straight their after work and see is we get the same issues 🤞  thought i try my luck here too, never know someone else might have had the same issue but thanks for the reply 
    • Basically your tuner needs to drive it for the 30 min (or whatever) to create the same conditions then check the ECU settings and sensors at that time. They may not be excited to because that takes them 30 min rather than just opening the bonnet and seeing the problem straight away.... Hot start is generally not as tricky as cold start, but there would be a table for fuel enrichment vs coolant temp as a starting point
    • Yeah, they all cant say anything for sure as everything is working fine . Said unable to find an issue untill it stops again. Could mist likely be CAS wiring or IAS valve issue but again not 100%
×
×
  • Create New...