Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

I saw a TVR in brisbane yesterday. Bloody heck it sounded nice.

Was that the Tusan S which is goldy/purple...I had a chat with the dude who owned it once. Wicked car.

wow so the BnR meet is over :banana:

So am I gona cop some heat for this or what?

Nah we'll just blame it on you...... :D

Oh real?

You gona chill in brissy for a while or u heading out to another site?

Yep really.

I have 3 weeks off, then I start work back in brissy, hopefully stay around there for a few months at least.

Yep really.

I have 3 weeks off, then I start work back in brissy, hopefully stay around there for a few months at least.

Oh good shit man :D

I got a mad amount of holidays building up so prob gona take a month off soon and just kick around the coast :banana:

Off to Melb next week though to do the great ocean road drive with the mrs and little man so thats something to look forward to for the time being :banana:

Oh good shit man :banana:

I got a mad amount of holidays building up so prob gona take a month off soon and just kick around the coast :banana:

Off to Melb next week though to do the great ocean road drive with the mrs and little man so thats something to look forward to for the time being :D

Sweet.

I have 1 week R&R saved...then its Perth for 2 weeks....in December I am heading over the Morten for a week. Man atm...life could not be more improved unless it was full of naked swimsuit models. :D

Wait wait, back up..... the bnr meet's over? What's all this about skids/cops??

I read back through 6 pages then thought I cbf... someone explain it for me please?

Wait wait, back up..... the bnr meet's over? What's all this about skids/cops??

I read back through 6 pages then thought I cbf... someone explain it for me please?

Look for the man in the yellow hat

wow so the BnR meet is over :banana:

So am I gona cop some heat for this or what?

Not from me, but please don't bring your 'friends' along to whatever eventuates to replace it. You and Mick are good in my book though :D

Wait wait, back up..... the bnr meet's over? What's all this about skids/cops??

I read back through 6 pages then thought I cbf... someone explain it for me please?

the 'crew' from the gold coast rocked up, and proceeded to make total d1cks of themselves in the BnR car park, so now the surrounding shops have complained, and apparantly the cops are going to be keeping a close eye on it there for a while.

Boostlosing would have loved it :banana:

I wish dad didn't have my ute at the moment, I'd go check it out tomorrow too see how many popo are there

Tdoggy-dog-dogg cums on a lot of things.

You said I was the only one . . . I thought I was special :(

Sweet.

I have 1 week R&R saved...then its Perth for 2 weeks....in December I am heading over the Morten for a week. Man atm...life could not be more improved unless it was full of naked swimsuit models. :D

Hahaha good to hear man.

Not from me, but please don't bring your 'friends' along to whatever eventuates to replace it. You and Mick are good in my book though :cheers:

;)

Morning all !!

Good morning :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...