Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

Dodgey carnt you are :D So did I read correctly that the 180 is up and running? When are you coming down for a visit?

im not dodgy, im just saying its an option to get a dodgy but tell the buyer its dodgy :/

as apposed to leading them to believe its legit

and yes 180 is running :D

timing is out and she backfires and gurgles like a champion

going in for a tune/set up timing dyno run either late this week/early next week - once the motor is run in :D

Yeah bin back a week. We had a new Site Engineer start last week on Monday and he quit today. Apparently he has wanted to get out of the industry for awhile and he's looking for a new path to follow. Seriously WTF are you thinking when you go to the interview for the job then. Such a dog act. We are down so many staff it's not funny.

That sux aye. Give John a Job :D

Skylines wrecked skyline resale. And p plate laws.

Who buys a skyline for resale though? Especially a dirty 32 GTS-T :/

I know you love your camber but I need grip damit :D

I don't understand... Camber is better for grip except when going straight, which is when you least need it.

...Unless of course you're drag racing. Which is ghey :D

Stealing my lines....sheesh

Mangs.

You love it

they dont even look at mods, if your horn works and you have no split CV boots and decent tyres you pass

That was what I thought too

im not dodgy, im just saying its an option to get a dodgy but tell the buyer its dodgy :D

as apposed to leading them to believe its legit

You should have seen the state my XF was in when it passed RWC.

My rule: Always assume a RWC is dodgy.

and yes 180 is running :D

timing is out and she backfires and gurgles like a champion

How far out? Don't want to damage that nice new diesel. I has a timing light... somewhere...

going in for a tune/set up timing dyno run either late this week/early next week - once the motor is run in :D

One day in the hills - run in done. Watch for speed cameras :(:/

you are such a lazy little fluffy, when i sold the R32 i went to a legit place and it passed easily, they dont even look at mods, if your horn works and you have no split CV boots and decent tyres you pass

And lights! Haha. Yea they're lazy and probably just do the obvious.

im not dodgy, im just saying its an option to get a dodgy but tell the buyer its dodgy :D

as apposed to leading them to believe its legit

and yes 180 is running :/

timing is out and she backfires and gurgles like a champion

going in for a tune/set up timing dyno run either late this week/early next week - once the motor is run in :D

Sounds good! Dinner date this Thursday night?

I don't understand... Camber is better for grip except when going straight, which is when you least need it.

...Unless of course you're drag racing. Which is ghey :D

This is true . . . And I am planning on getting my lazy ass to tha track one of these dayz

im not dodgy, im just saying its an option to get a dodgy but tell the buyer its dodgy :D

as apposed to leading them to believe its legit

and yes 180 is running ;)

timing is out and she backfires and gurgles like a champion

going in for a tune/set up timing dyno run either late this week/early next week - once the motor is run in :)

Noice. What's done to the motor? Did you rebuild it? I thought you just bought a second hand one?

That sux aye. Give John a Job :D

I would but I refuse to recommend anyone for a job. That last guy was recommended to us by one of the Project Engineers and it makes him look like a dick when that guy quits lol.

Who buys a skyline for resale though? Especially a dirty 32 GTS-T :D

This is true.

I don't understand... Camber is better for grip except when going straight, which is when you least need it.

...Unless of course you're drag racing. Which is ghey :(

:/

Give me one too. I need a job change.

I do too, but this job pays too well

This is true . . . And I am planning on getting my lazy ass to tha track one of these dayz

Good stuff :D

I would but I refuse to recommend anyone for a job. That last guy was recommended to us by one of the Project Engineers and it makes him look like a dick when that guy quits lol.

LOL yeah. That is true.

Noice. What's done to the motor? Did you rebuild it? I thought you just bought a second hand one?

rebuilt motor mang 0km :D

well now 283km on it hahaha

how are you running it in sexy?

so far just have been taking the back streets everywehre - trying to vary speed / load - havnt taken her past 3500rpm

going to do an oil change tomorrow and then head up the mountains to finish off the last 250km or so of her run in, then get her on the dyno to sort out all the shittttttt

so far just have been taking the back streets everywehre - trying to vary speed / load - havnt taken her past 3500rpm

going to do an oil change tomorrow and then head up the mountains to finish off the last 250km or so of her run in, then get her on the dyno to sort out all the shittttttt

Do a skid :D

so far just have been taking the back streets everywehre - trying to vary speed / load - havnt taken her past 3500rpm

going to do an oil change tomorrow and then head up the mountains to finish off the last 250km or so of her run in, then get her on the dyno to sort out all the shittttttt

Start giving it some more revs, you don't want to baby it too much or you'll have a soft motor.

I don't mean redline, but maybe 5000rpm (whats an SR Rev to?).

You need to let the rings bed in over a large range of both load and RPM

Start giving it some more revs, you don't want to baby it too much or you'll have a soft motor.

I don't mean redline, but maybe 5000rpm (whats an SR Rev to?).

You need to let the rings bed in over a large range of both load and RPM

SR redline is 7500, alright ill start a little more tehehe

ps martin i think im a real contender to challenge your epic dose :ermm: - she doses nicely, especially considering the boost is set on 4psi

Dyno run in FTW, the run in on Annas car took an hour and cost like $70...WIN

Now just have to finish the tune :S

Hills run in FTW. Although with the speeding ticket, it actually cost me more than that :ermm:

Next time maybe I'll go the dyno option :D

ps martin i think im a real contender to challenge your epic dose :P - she doses nicely, especially considering the boost is set on 4psi

I approve <3

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
×
×
  • Create New...