Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

Was truly awesome. I went out briefly for an excuse to use my fog lights :thumbsup:

I don't have fog lights :). Sh*ts me off how many people were driving with NO lights though. FFS people, turn your lights on! Might not help you see, but helps you BE SEEN

That's awesome. How much adjustability do you have though?

Probably not much. Camber is adjustable via shims

Could be that deadly fog that turns people inside out. I here it has been getting around again.

Wut?

Cricket last night was awesome. Opened the batting and got 64 (4 overs), only went for a few runs in my two overs bowling, and took a caught and bowled landing on my dicky elbow.

Team still lost though :thumbsup: and I've been driving 1 handed as my elbow f*cking kills. Nice to find some form before the corporate games on the weekend though :)

I don't have fog lights :thumbsup:. Sh*ts me off how many people were driving with NO lights though. FFS people, turn your lights on! Might not help you see, but helps you BE SEEN

parkers are always a safe bet. but people are stupid and think it'll blind them...

Also, concrete carparks in the wet are too easy

i has wittnessed

Nakie

f**k man. now i have to stay at my desk for 5minutes to wait until it calms down :(

I don't have fog lights :( . Sh*ts me off how many people were driving with NO lights though. FFS people, turn your lights on! Might not help you see, but helps you BE SEEN

Probably not much. Camber is adjustable via shims

Wut?

Touche. Would be a bit of a prick adjusting it then eh.

Cricket last night was awesome. Opened the batting and got 64 (4 overs), only went for a few runs in my two overs bowling, and took a caught and bowled landing on my dicky elbow.

Team still lost though :( and I've been driving 1 handed as my elbow f*cking kills. Nice to find some form before the corporate games on the weekend though :)

Good show old chap.

i has wittnessed

f**k man. now i have to stay at my desk for 5minutes to wait until it calms down :(

Hot.

Touche. Would be a bit of a prick adjusting it then eh.

Once it's shimmed up to 'epic-camber-stance-offset-win' there won't be any need to adjust it :(.

Good show old chap.

I say, jolly good. Cup of tea, old chap?

Once it's shimmed up to 'epic-camber-stance-offset-win' there won't be any need to adjust it :( .

I say, jolly good. Cup of tea, old chap?

Make your own shims out of 10mm steel plate.

Sounds delightful Martin. Scones too?

yeesssssssssssssssssssssssssss! skidzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzzz

aaaaaaaaaaaaaahhhhhhhhhh

sup with you guys?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...