Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

Blah blah blah lost my original post and cbf re-doing it. Basically:

Yeah mang!

Screw those losers

That's what she said

That's what she said

That's what THEY said about what she said

Mmmm I like pie too

I believe I already asked about wednesday for german club... therefore I'm in

flamin mongrel REPLY TO ME I f**kING MISS YOU

flamin mongrel REPLY TO ME I f**kING MISS YOU

Sorry bro I did have something in my original post for you......

I showed up at like 930 or 10 or somethin... so you defs should stay later :)

Next week / german club?

Edited by mosquitocoils
One word.

AWESOME!

Thats me alright

Poor work today chaps

Where were you ? :D

hallo hallo hallo.....whadhaveweere?

Evening squire. *adjusts pipe*

Hung over from Diwali celebrations ;)

Whats a diwali ? :P

That's what she said

night all

Afternoon.

I'm dead inside.

Need less alcohol still active, and more sleep to take place right.........meow.

I need to start drinking more. WEnt through half a bottle of jack last night.

Prolly hit up dan murphyhs for a few bottles of wine.

two bottles of wine is a good way to get hammered.

Cheap as well =D

I need to start drinking more. WEnt through half a bottle of jack last night.

Prolly hit up dan murphyhs for a few bottles of wine.

two bottles of wine is a good way to get hammered.

Cheap as well =D

Goon you say.... hmmm $8 for four litres... In :)

joshwa, how big rims would i need to clear these?

http://cgi.ebay.com.au/ws/eBayISAPI.dll?Vi...e=STRK:MEWAX:IT

996 came with 17's and 18's, they should fit under most 17's pending clearance/wheel centre disk etc

if they don't clear 17's .....

grinder time!

In other news, my garage is finally clean and compressor setup in a good position. I also put the suspension back in the front of the project 31, need to get the gaurds rolled

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...