Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

Hello all.

how was the weekend? Mine consisted of 'Pain da fens... up, down, uuuuuuuup, dooooooooooooooown......'

McRae - backstreet boosting in an unrego'ed car? noice

McFly - The federal 535 is a pretty quick street type tyre. Don't expect too much from them. Not saying they're not grippy, but they are not a flash tyre. Good to hear that your wheel was fixable.

Mr Marine chronometer - Did you sort out your misfire problerm???

Hello all.

how was the weekend? Mine consisted of 'Pain da fens... up, down, uuuuuuuup, dooooooooooooooown......'

McRae - backstreet boosting in an unrego'ed car? noice

McFly - The federal 535 is a pretty quick street type tyre. Don't expect too much from them. Not saying they're not grippy, but they are not a flash tyre. Good to hear that your wheel was fixable.

Mr Marine chronometer - Did you sort out your misfire problerm???

Lol I considered putting the 31 plates on it but then just decided f**k it n went without plates. I want it back on the road now though lol :D

Just spent 3.5 hours inspecting a wall with the engineer. f**kin gay.

No one ever said that these walking gant chart guys were employed for having any relevant knowledge! (including maths, or the ability to read gant charts)

Walking gant chart man just asked why my hours this week were less than last week, when in fact i did 1 hour more :D

Clearly he is deducting hours spent on SAU as non working lol

No one ever said that these walking gant chart guys were employed for having any relevant knowledge! (including maths, or the ability to read gant charts)

Yeah PMs are there to make everyone else hate life.

Martin - yes 535s are good street tyres.

I have stolen coil pack 1 and 2 and the loom from your ute. I covered it back up again. Haven't put any other parts into it yet because it 1. may not be the problem. 2. I need a vacuum to get all the leaves out so I can put things back where they came from. and 3. I dropped a screw and need needle nose pliers or a magnet stick to get it out.

Edited by Isola

nah it was sitting there behind the 31, just got moved to mine yesterday, will need to make some time to work on that thing too.....

Martin - yes 535s are good street tyres.

I have stolen coil pack 1 and 2 and the loom from your ute. I covered it back up again. Haven't put any other parts into it yet because it 1. may not be the problem. 2. I need a vacuum to get all the leaves out so I can put things back where they came from. and 3. I dropped a screw and need needle nose pliers or a magnet stick to get it out.

I have an extendable magnet stick thingo if you need to use it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • This. The R34 handbrake icon DOES come up when the brake fluid level is low. You might be sitting right on that threshhold. I have been down this diagnosis path and this was the solution (and it was pretty much as full as your picture is to begin with).
    • Unfortunately the cavaet to that is that while any scan tool should be able to read the code, the workshop will need a consult plug to OBD socket adapter. You don't have a location on your profile, where are you based?
    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
×
×
  • Create New...