Jump to content
SAU Community

Shannons Wheels Show - Final Numbers...

Frink

By Frink,
in Australian Capital Territory

 Share

Recommended Posts

TURISMO Experienced

TURISMO

Posted
Posted
BYO Chair and drinks

And to you bl00dy chair thieves, if you don't bring a chair, don't steal someone elses :pirate:

I promise I will not take them home.....

im going to take everybodys chairs :P

Team Monochrome Ninja's :P:ninja:

JD_R33 Proficient

JD_R33

Posted
Posted

If anyone from the deep south wants to join our little convoy, we will be leaving from the Calwell servo around 8:00am or shortly after.

Going by people I know from other car clubs that are attending, we are likely to be setting up in the grassed area between King Edward Tce and Reconciliation place. But I could be wrong.

Did anyone actually hear back from the organisers? They have usually sent each club a site map by now.

OZR32GTR Collaborator

OZR32GTR

Posted
Posted

Hey guys!

Haven't posted for a while.

I'll bring my R32 gtr along under the proviso that my wifey doesn't go into labour :D

Will prolly get there around mid morning-ish...

Do we know what area we're in yet?

Cheers,

Brad

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • WMDC35
      Wheel Sizes & Offsets For Skylines

      By WMDC35 · Posted

      A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Duncan
      RB20DE NEO smallbox clutch.

      By Duncan · Posted

      Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...