Jump to content
SAU Community

Recommended Posts

Hay

I just had a dyno done to me car it is putting 183rwks i was advised by someone that i should upgrade the oil pump, he reckons that that kind of power i should upgrade i want to put a boost T on aswell to push it to 200rwks, is this true about the oil pump

cheers

Link to comment
https://www.sau.com.au/forums/topic/262212-oil-pump/
Share on other sites

I'm only pushing 170RWKW's in my RB20 and I just did a big end bearing up at wakefield due to oil starvation. In saying that I was bouncing of 7500 rev limiter (maybe not bouncing but it was a drift day) and had the car being thrown around fairly violently.

So unless you are belting your car side to side, and redlining it, you don't have much to worry about, But i would do it if you were building your motor :)

Link to comment
https://www.sau.com.au/forums/topic/262212-oil-pump/#findComment-4492452
Share on other sites

Yes - on the proviso you have done the rest of the mods.

183 rwkw in a GTS-t is very good so I suspect you have a few mods already. FMIC, Zorst, Turbs, Puter etc....If you want to push 200rwkws - safe not sorry. Spend now and save later. Would you risk an engine rebuild?

Link to comment
https://www.sau.com.au/forums/topic/262212-oil-pump/#findComment-4498352
Share on other sites

Its an 94 r33 gtst This is My first nissan skyline so i am not sure on what mods i need to do so it does not blow my engine and to get more power

Ok, as its your first skyline ill be very blunt;

-Changing oil pumps in a GTST is a waste of time with that power level, or if its working fine

-You will break the oil pump if you bounce off the redline time and time again

-Always warm up before using more than 30% throttle on cold start

-Always cool down (fit a turbo timer if you're a leadfoot)

-Before adding power, sort out suspension and a short shifter for the gearbox

-Once you've got it sorted suspension wise look for more power

Powerwise;

-FMIC (forum sponsors)

-EBC (forum sponsors)

-HKS GTRS kit (forum sponsors)

-ECU, ideally one that uses MAP vs TPS for mapping (forum sponsors)

-Quality exhaust including highflow cat, good dump pipe (forum sponsors)

:/

EDIT: If you need any further clarification, call a few workshops and get quotes for "just a new oil pump fitted" :laugh:

Link to comment
https://www.sau.com.au/forums/topic/262212-oil-pump/#findComment-4502476
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
    • And yes with a full tank it will hit limiter free revving or driving 6B6CDF6E-4094-426D-A9CB-6C553475FE36.mp4
    • One way of putting the fuel surge idea to rest, is that even when in neutral/clutch in or free revving it still has the same issue, it can’t even get to limiter (7800) so to me that says it can’t be g force, I’m not trying to argue I just want to find the f&$king issue 😡
×
×
  • Create New...