Jump to content
SAU Community

Rb25/30 Engine Package, Requires Machining & Assembly

Shano3000
 Share

Recommended Posts

Shano3000 Proficient

Shano3000

Posted
Posted

Parts include:

Rb25de non vct head from a R32. Head has been cleaned, new valve stem seals, heavy duty springs for turbo application and surface machined flat.

Inlet manifold, injectors and fuel rail, Coil packs, throttle body and all bolts/miscelanious pipes etc.

Series 2 RB30 block, requires maching bore/hone etc. Crankshaft also requires machining. Standard rods & all bolts required for assembly.

Good Condition S2 RB30 Bottom End, fully assembled. Brought as working motor and stripped head etc off

New ACL cast RB30 pistons, rings and bearings. Pistons are 1mm oversize and bearings .25mm oversize.

RB30 complete engine gasket kit with Headgasket.

Pistons are for a RB30 non turbo, so when assembled with RB25DE head will give compression ratio of around 8.3-1

As stated the block will need to be bored 1mm oversize to accomodate the pistons and the crankshaft ground .25mm for the bearings. This is a complete package and once assembled will handle up to 350rwkw. Was planning to assemble this engine and put in my R32 although being a full time student i just dont have the cash.

Price $1000 for the lot. Contact through PM or call on 0422816780.

Pictures : http://s160.photobucket.com/albums/t177/Shano3000/

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Nismo GT Pro LSD configurations

      By Kinkstaah · Posted

      I don't know if you can disassemble the thing and put it backwards for different ramp rates. They're both "2 ways" or both "1.5 ways" because well, 2 ways and 1.5 ways are the same 'thing' I do not know for sure, but I believe the 38420-RSS15-B5 is the 1 way, and 38420-RSS20-B5 is the two way. In other words, I predict Nissan considers this: to be a 1.5 way. No idea what actually happens when it arrives/you disassemble it. It would be an excellent question to ask Nismo directly! I somehow doubt you will get an answer though, I feel you would be the first person to document what you encounter when you open the box and the internet would be grateful.
    • Duncan
      Replacing Fuel Pressure Regulator

      By Duncan · Posted

      I'm going to slap an old nismo logo sticker on my spare one and sell it to the land of the free for a thousand bucks
    • Duncan
      Replacing Fuel Pressure Regulator

      By Duncan · Posted

      lol, probably should have read further!
    • R32 TT
      33 GTR Broken front wheel knuckle

      By R32 TT · Posted

      Well - they have arrived.  And they are easy on the eye to put it mildly... These only have three bolts - but for a start there is a key that fits with vacuum like precision..  And as you can see by my ruler, the interface is large..   I listened to a podcast on HP Academy about Dan (KiwiCNC) and I'm more than comfortable he knows what he is doing. R35 Bearing assembly should arrive later today so can mock that up for a look. Can't wait to get these on and get some brake pressure logging too. IMG_3860.MP4
    • GTSBoy
      Nismo GT Pro LSD configurations

      By GTSBoy · Posted

      I would be very confident that they are the same parts (the 2 different SKUs). It seems very clear that you can drop the cam in the 2-way opening, or in the other opening. If you arrange it in the other opening in the same way that you see any other 1-way diff, ie, with the flat of the cam up against the 1° side of the opening, then it would work as a 1-way. It can only spread the ramps when driving forwards - cannot spread the ramps on overrun. It would then appear obvious that if you put the cam into the opening "backwards", that you would get the angled flats of the cam working onto the "points" of the 1° side of the opening, which would give you ramp spread in both loading directions. I do wonder if the forward direction of the 1.5-way config is equivalent to the forward direction of the 2-way, seeing as the cams are flipped and the angled surfaces on those would need to be the same on each side - AND - clearly when installed in either the 2-way or 1-1ay configuration they are not intended to work exactly the same (the ramp angles on the 2-way are 10° different between forward and backward, and the ramp doesn't exist in the 1-way config). 'twere me, I think I would rather actually have a set of rings that offered the 2-way with two different sets of ramp angles, say the 55/45 of the existing design and maybe a 45/37.5 combo for a less aggressive effect), AND another set of rings with a dedicated 1.5-way opening and a dedicated 1-way opening. The 1.5-way opening would actually have the steeper angle on the overdrive side that causes it to be less pushy than the forward drive angle, like you see in many other diffs. But really - if this Nismo thing is thought out properly and all those surfaces work on each other the way that they need to, who am I to argue?
×
×
  • Create New...