Jump to content
SAU Community

Recommended Posts

Guys I purchased some cp pistons for rb26 part number SC7310 86.5mm (20thou) over 7 months ago,I just found out off engine builder I need 87mm (40 thou) :D so I need to sell these quick and get correct ones.These are 8.5.1 compression.I'm looking for $800 express delivered aus wide

Pm if any questions

Cheers Tunksy

Edited by Fumes21
Link to comment
https://www.sau.com.au/forums/topic/263287-new-cp-pistons/
Share on other sites

Guys I purchased some cp pistons for rb26 part number SC7310 86.5mm (20thou) over 7 months ago,I just found out off engine builder I need 87mm (40 thou) :D so I need to sell these quick and get correct ones.These are 8.5.1 compression.I'm looking for $800 express delivered aus wide

Pm if any questions

Cheers Tunksy

where are you located?

Link to comment
https://www.sau.com.au/forums/topic/263287-new-cp-pistons/#findComment-4506214
Share on other sites

Guys I purchased some cp pistons for rb26 part number SC7310 86.5mm (20thou) over 7 months ago,I just found out off engine builder I need 87mm (40 thou) :down: so I need to sell these quick and get correct ones.These are 8.5.1 compression.I'm looking for $800 express delivered aus wide

Pm if any questions

Cheers Tunksy

Hello, Tunksy

I am chasing a set of forged pistons RB26 +20thou. Where are you located? plz call Alex on 0433559972 asap. I suppose the pistons will come with the rings and pins. cheers

Link to comment
https://www.sau.com.au/forums/topic/263287-new-cp-pistons/#findComment-4508466
Share on other sites

bad trader buyer beware!

I purchase these apparent cp pistons from this tunksy bloke for $800 but was sent genuine nissan pistons instead, I asked for his number and he gave me a guy who was looking to purchase the pistons as well

If anyone knows this guy can you please send me his number and email addy as well

Edited by erayza
Link to comment
https://www.sau.com.au/forums/topic/263287-new-cp-pistons/#findComment-4517383
Share on other sites

i was going to buy these pistons, lucky i didnt.

I asked this seller to do COD but he said he needed the money and wanted bank transfer instead. I then asked him to sell them through ebay and id buy them and he still declind. Thats when i walked away as he sounded sus.

Sorry to hear this happened. Its becoming more and more commen which is a shame.

Link to comment
https://www.sau.com.au/forums/topic/263287-new-cp-pistons/#findComment-4519901
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, this is probably where a wiring diagram and a multimeter come into play.
    • I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...