Jump to content
SAU Community

New Cp Pistons

Fumes21
 Share

Recommended Posts

Fumes21 Contributor

Fumes21

Posted
Posted (edited)

Guys I purchased some cp pistons for rb26 part number SC7310 86.5mm (20thou) over 7 months ago,I just found out off engine builder I need 87mm (40 thou) :D so I need to sell these quick and get correct ones.These are 8.5.1 compression.I'm looking for $800 express delivered aus wide

Pm if any questions

Cheers Tunksy

Edited by Fumes21
Link to comment
https://www.sau.com.au/forums/topic/263287-new-cp-pistons/
Share on other sites
white180sx Proficient

white180sx

Posted
Posted
Guys I purchased some cp pistons for rb26 part number SC7310 86.5mm (20thou) over 7 months ago,I just found out off engine builder I need 87mm (40 thou) :D so I need to sell these quick and get correct ones.These are 8.5.1 compression.I'm looking for $800 express delivered aus wide

Pm if any questions

Cheers Tunksy

where are you located?

Link to comment
https://www.sau.com.au/forums/topic/263287-new-cp-pistons/#findComment-4506214
Share on other sites
Tim GTR Proficient

Tim GTR

Posted
Posted
Guys I purchased some cp pistons for rb26 part number SC7310 86.5mm (20thou) over 7 months ago,I just found out off engine builder I need 87mm (40 thou) :down: so I need to sell these quick and get correct ones.These are 8.5.1 compression.I'm looking for $800 express delivered aus wide

Pm if any questions

Cheers Tunksy

Hello, Tunksy

I am chasing a set of forged pistons RB26 +20thou. Where are you located? plz call Alex on 0433559972 asap. I suppose the pistons will come with the rings and pins. cheers

Link to comment
https://www.sau.com.au/forums/topic/263287-new-cp-pistons/#findComment-4508466
Share on other sites
erayza Contributor

erayza

Posted
Posted (edited)

bad trader buyer beware!

I purchase these apparent cp pistons from this tunksy bloke for $800 but was sent genuine nissan pistons instead, I asked for his number and he gave me a guy who was looking to purchase the pistons as well

If anyone knows this guy can you please send me his number and email addy as well

Edited by erayza
Link to comment
https://www.sau.com.au/forums/topic/263287-new-cp-pistons/#findComment-4517383
Share on other sites
white180sx Proficient

white180sx

Posted
Posted

i was going to buy these pistons, lucky i didnt.

I asked this seller to do COD but he said he needed the money and wanted bank transfer instead. I then asked him to sell them through ebay and id buy them and he still declind. Thats when i walked away as he sounded sus.

Sorry to hear this happened. Its becoming more and more commen which is a shame.

Link to comment
https://www.sau.com.au/forums/topic/263287-new-cp-pistons/#findComment-4519901
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • WMDC35
      Wheel Sizes & Offsets For Skylines

      By WMDC35 · Posted

      A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Duncan
      RB20DE NEO smallbox clutch.

      By Duncan · Posted

      Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...