Jump to content
SAU Community

Recommended Posts

Hey guys, need to replace my tie rod ends on my 32 gtst.

Have been quoted $130 each from nissan, $23 each from autobarn, or adjustable ones from Just jap for $149 for the pair (see image)

post-29295-1238401010_thumb.jpg

Looking at getting the ones from autobarn as I cant see why nissan ones are worth 5 times more. Has anyone replaced their tie rod ends with generic ones and had a bad experience?

Also, could anybody shed some light on what is adjustable on the just jap ones? Obviously they can be wound in and out. It appears that the bolt on the top might allow for some form of adjustment?

Any ideas?

Cheers

Edited by mark32gts-t
Link to comment
https://www.sau.com.au/forums/topic/263393-replacement-tie-rod-ends-r32-gtst/
Share on other sites

all tie rod ends are adjustable... thats how you change the toe settings on your front wheels. the ones from just jap would be the better option over the autobarn ones... they have pillowballs in them meaning reducing movement in the tie rod ball and giving a more direct steering feel.. but it will be harsher.

i really cant see how the just jap ones are adjustable in any other way than winding them in or or out on the tie rod.. unless you can wind the ball end out of the little housing, so you can wind the housing further on the tie rod if you have steering lock spacers to increase steering lock...

If the autobarn replacement ones are simply OEM-style replacements, you may as well go for them. The ones I fitted recently seemed good quality, as good as factory. I would not waste the extra money on the nissan ones.

I've got a set of Pedders tie rods on my 32, probably the same as the autobarn ones - I paid about $20 odd bucks each.

Had them on the car for 6 months now with no problems. I wouldn't bother with the justjap/nissan ones

Yes I think I shall be getting the ones from autobarn. I called fulcrum today to get a quote on a wheel alignment after I replace the tie rods and asked about the legality of rose joint tie rod ends. The guy I spoke to wouldn't comment and said I should contact QLD transport. Which makes me think they might not be legal. So I wonder what insurance would say if for some reason I had to make a claim and they found "illegal" steering components on the vehicle. Cheers for the input

very few aftermarket parts are "legal"

nissan and nismo, toyota and trd etc. parts are so expensive because they are all adr tested and comply with any regulations etc. they have to cover the cost of testing and r&d so they charge $130... then someone in china gets the nissan part and makes a cheap knock off, with no testing etc. and sells it for $20.

all the aftermarket company has to do is have a tiny warning on the packaging saying "off road or race use only" or "check legality in your state" and they are covered.

almost every modification you make is illegal.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...