Jump to content
SAU Community

Recommended Posts

Is this the R33 AFM? (Circled red)

http://i300.photobucket.com/albums/nn37/no...ous_azn/AFM.jpg

If so, how do I open it and clean it? I have CRC MAF.

That is the Airflow meter, not sure what you mean a CRC AFM, but this one looks standard.

In my opinion you can not open the AFM box itself, so do not try... There are some people that can repair if there is a problem but it is filled with hard resin and needs to be looked at by a professional.

I believe it can be re-built but not by you if you don't know how.

They either work or they don't, sometimes they will cause a rough idle and hesitation but they will normally either stop the car or not.

As for cleaning the AFM, only do this when the engine is cold, (at least an hour after turning off) with the Ignition Key off.

Pull the airbox cover off like you have.

Remove the following;

2 bolts holding the lower half of box at front of car

1 bolt on the aft outside

1 on the aft inside.

Hose Clamp that holds Hose to the AFM

Squeeze Tab on Electrical Plug, Push in and then pull terminal up to disconnect AFM from Car Loom.

Then lift the box gently off it's mounts and remove it from Car.

Turn box over and spray Electrical Contact Cleaner down the AFM (probe hanging in the inlet tube) and into the gauze that opens into the Airbox. Use the spray in the reverse direction of Airflow and do not touch the Probe, just use the spray and make sure you get a non residue drying type of cleaner.

Spray both sides of Electrical connection, the 3 pins need to look really clean.

Let it dry for a minute, then re-assemble in reverse... making sure you hear a click on the Electrical re-connection.

Should run a bit smoother now, especially if you have an oiled Air Filter element installed in Airbox.

Link to comment
https://www.sau.com.au/forums/topic/263869-r33-afm/#findComment-4515487
Share on other sites

yep thats the air flow meter alright........................

have a look.......

not being able to see your car........

i feel that there is more to it than just an air flow meter......

alot of people having the same symptoms as yours, end up cleaning with AFM withought any improvement....

but it doesnt hurt to try

let us know how you go

Link to comment
https://www.sau.com.au/forums/topic/263869-r33-afm/#findComment-4516640
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...