Jump to content
SAU Community

Recommended Posts

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

got any more 4 door 32 parts for sale?? how much for the skirts posted to nsw 2323?

I will measure them up and sent u a quote this weekend.... What other 4 door specific parts are u after??

  • 4 weeks later...
  • 3 weeks later...
  • 3 weeks later...
  • 3 weeks later...
im also after 4 dr parts... wot do u have in terms of bodykit, suspension

4 dr side skirts are still for sale as are the Cusco castor rods, all the rest is gone..

  • 4 weeks later...

Still for sale

tubular bolt in 6 point roll cage with padding, plates, bolts. Came out of a D2 car from Japan, built for R32, not too sure what other cars it would fit into, possibly laurel/cefiro

$1000ono

R32 4 door type M side skirts, rare

$250pair ono

Genuine Cusco pillow ball castor rods/arms suit R32 gts/t S13

$250ono

Whiteline R32 front & rear strut braces, practically new

$320

R32 impul front sway bar with D-shackles & bushes

$100ono

R32 gtst manual standard computer, 93’ model, un chipped

$150ono

R32 type m front bar damaged on LHS,

$80 ono (pick up only)

Exedy Clutch Kit

This is a Heavy Duty Clutch Kit for the following:

Nissan Skyline RB20DET & RB25DET

R31- 1987-89 2.0Lt

R32- 1989 onwards 2.0Lt

R33- 1993 onwards 2.5 Lt

Purchased from CBA WA for $450

Clutch is practically new save $$

Clutch was used for approx. 2-3months on RB20DET powered Nissan skyline R32 with 210-220rwkw without slipping once. Very street-able clutch with good pedal feel (heavier than standard) and friction , clutch had a very easy life for the short period it was in my car (i don’t track or drift my car), data sheet that i have from when i bought the car says it has following specs:

clamping load = 2400 LB

faces = 2

Radius =7.625

Friction coefficient = 0.3

Torque = 457.6 ft/lb @ 4500 rpm

Horsepower = 392 HP

$250

RB20 clutch fans 1left

$40 each

Trust S15 exhaust and cat convertor. 2 parts held together with TRUST stainless clamp.

Has 'Jasma' plate on it (whatever that means)

Stainless rear cannon muffler (few scratches as seen in pictures but no dents)

Rest of exhaust and second muffler made from mild steel, painted in high temp matt paint.

Cat convertor is near new but is welded in place,

$700ono

Aluminium intercooler piping, lipped either end, 3” mandrel bent

$20 pair

R32 RB20 cam gears, standard parts, prefect condition, no wear on teeth, come as pair but may split

$50ono

R32 s13 front left lower control arm

$30

Nolathane ‘D’ shape bushes

Repco part no.

42150 (x2) 24mm ID/ 31mm OD

42937 (x2) 27mm ID /31mm OD

D shackles, for sway bar, tried to fit but never used, comes with grease sachet

$20

R32 ashtray with Apexi badge, rice up your interior with this fine specimen

hey looking for some rear suspension can u help me out for a R32?? cheerrsass

Sorry Jasmine, all the stuff that was for rear suspension has been sold. What exactly were u after?? Only have strut braces and bushes for a sway bar.

Cheers

Rob

  • 3 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...