Jump to content
SAU Community

Recommended Posts

Tein Type HA Coilovers

Greddy Profec B (set to 10psi low/13psi high)

Nismo shift knob

Momo Steering wheel

3" Exhaust (cat-back)

Nismo GT2 (with brand new tyres)

Exedy Sportstuff clutch

GTR Front seats

GTR front bar and rio

GTR rear guards

GTR fuel pump

GTR Vspec II boot lid w/ Genuine N1 lip

FMIC

Everything else is factory including factory electric sunroof, folding mirrors and digital climate control all still works

FYI Points:

* Rear interior trim (around rear window) needs replacing (due to dodgy complience) but whole interior could use a decent clean

* Stereo doesn't work (wiring/lazyness issue)

* Gearbox very noisy and 2nd gear synchro broken. Gearbox currently out of the car.

* Needs a decent clean and polish

Engine feels strong, but whole car could use some TLC as it has sat in the driveway for the last 5 months as I ride to and from work and spend most off-shift-time working on the EVO.

Due to the fact it has no gearbox, I am willing to deliver the car on purchase at no cost to buyer OR install a supplied box at no charge.

Rego till the end of June

$9000neg

Link to comment
https://www.sau.com.au/forums/topic/265341-nsw-93-r32-nissan-skyline-gts-t/
Share on other sites

Sale fell through.

Now selling with added gearbox goodness :) $8000 firm

It has been noted that the rear guards may not be genuine GTR but have definatly been pumped/rolled/etc to fit GTR size/offset wheels under.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...