Jump to content
SAU Community

Swapping 17inch Bronze Te37s With Tyres

bin
 Share

Recommended Posts

bin Community Regular

bin

Posted
Posted (edited)

Item:VOLKS TE37 17Inch Bronze

Condition: All 4 wheels have gutter rash. (came like that with the car)

Front Tyres: Gemstone 215/45/17 with 90%tread

Rear Tyres: Federal 595 RS semi slicks 235/45/17 with 80% tread

Rears are wider than the front by 1 inch.

Offset fits R33 GTST perfect. Not sure about the widths though.

Ok so heres the deal, I'm looking to swap for a decent looking set of 18s WITH decent amount tread on tyres.

The 18s must fit an R33 GTST. Would prefer to swap in person in Sydney.

Post up pics of the rims you wanna swap me or just pm me. Pics of the rims on my car are attached below.

Feel free to give me a call at 0433 712 092.

post-55566-1240018688_thumb.jpg

Edited by bin
~Hypnotik~ Rising Star

~Hypnotik~

Posted
Posted

You won't have any luck unless you post up the widths and offsets. Look inside the wheel, there should be a sticker on the inner rim with the size and offset, otherwise it will be stamped onto the back of the hub

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • r32-25t
      R32 gtr transmission strength, billet plate

      By r32-25t · Posted

      Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...