Jump to content
SAU Community

Canberra Sandblasting

INVRTD

By INVRTD,
in Australian Capital Territory

 Share

Recommended Posts

INVRTD Proficient

INVRTD

Posted
Posted

Howdy Guys,

A bit of an update on my progress (ive actually started fixing my car, yay), i have pulled the front bar off my car to fix it, and have found i have lots of rust on intercooler piping and other parts, i am to lasy to take it off myself so i want to sand blast the items. Does anyone know where in caberra to sandblast stuff?

Cheers,

I can't wait to get back on the road with a working car,

Link to comment
https://www.sau.com.au/forums/topic/266210-canberra-sandblasting/
Share on other sites
Baconer Grand Master

Baconer

Posted
Posted
theres a place just off woolongong street called A1 Sandblasting, its down a VERY bump long driveway out through a metal scrapyard, a few farmer like fellas in a BIG shed, yellow and black sign on top

i got 2 rims done for 60 bucks

I got my whole car sandblasted there, cheap, good work and fast turnaround

AA Sandblasting - 6280 5128

Its an absolute bastard to find though, its across the road from BDL stereo down a long shitty driveway

Baconer Grand Master

Baconer

Posted
Posted

Theres 2 main forms of sandblasting.

Sandblasting will remove rust but they generally will not use this on panels because the heat produced will distort the panels

Beadblasting is a less abrasive form of sandblasting and will remove paint without creating too much heat or distortion, there will be small amount that may be noticable to the panel beater who picks the car up afterwards.

With my car they sandblasted the engine bay, under panels, wheel wells and door jams then bead blasted the rest. Unless you had huge amounts of rust (eaten away sections of metal) the sandblasting shouldnt punch too much out. If it does though its probably for the best because you'll need it plated anyway.

INVRTD Proficient

INVRTD

Posted
  • Author
Posted

alex,

how mucd did the enginebay cost to get done?

I have some rust on lower intercooler piping, its surface rust, i jsut want to get rid of it and ill repaint it, there is a couple of braces that i want to get done too, but i wouldnt mind redoing the entire engine bay, depends on cost.

alex

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • GTSBoy
      remote oil cooler hose size, 8,10 or an12?

      By GTSBoy · Posted

      I will rebutt this and the preceding point from Dose....but without doing any calcs to demonstrate anything and without knowing that I am right or wrong. But... The flow capacity of a fluid transfer system is not limited by the smallest orifice or section of conduit in that system, unless it is drastically smaller than the rest of the system. OK, I use the word drastically perhaps with too much emphasis, but let's drill down on what I really mean. The flow capacity of the system is the result of the sum of the restrictions of the entire system. So, to make an extreme example, if you have a network with 3" pipe everywhere (and let's say a total length of only a few metres) and that 12mm ID restriction of the oil filter connection being the obvious restriction, then for any given amount of pressure available, the vast majority of all the pressure drop in the system is going to occur in the 12mm restriction. But.... increase the length of the 3" pipeline to, say 1000m, and suddenly the pipe pressure loss will likely add up to either be in the same order of magnitude, possibly even exceeding that of the 12mm restriction. Now the 12mm restriction starts to matter less. Translate this to the actual engine, actual oil cooler hose sizing, etc etc, and perhaps: The pressure loss caused by flowing through the narrow section (being the 12mm oil filter port, and perhaps any internal engine oil flow pathways associated with it) is a certain number. The pressure loss through, say, -12 hoses out to the cooler and back is negligible, but The pressure loss through -10 hoses out to the cooler, at the exact same length as the above, starts to become a decent fraction of the loss through the 12mm stuff at the filter port. Maybe even it starts to exceed it. I could actually do these calcs if I knew 1) how much oil was actually flowing in the line, 2) gave enough of a f**k to do things that I hate doing for work, voluntarily for a hypothetical discussion. Anyway - I reiterate. It's not the narrowest port that necessarily determines how much it can all flow. It is the sum. A long enough length of seemingly fat enough pipe can still cause more loss than a semmingly dominant small bore restriction.
    • MBS206
      remote oil cooler hose size, 8,10 or an12?

      By MBS206 · Posted

      To pick up what Dose is putting down. Not a lot of point running a huge hose if the motor is still restricted to the smaller size... It's only capable of flowing so much at that point...   *Waits for GTSBoy to come in and bring in the technicalities of length of pipe, and additional restriction from wall friction etc etc*
    • QB6SAGR
      Tein Circuit Master- rebuild worth it?

      By QB6SAGR · Posted

      Hooley Dooley these things have some history! If i sell them they will need a certificate of providence to prove they have been in the hands of verified RB20 royalty! They have been stored in a plastic tub, away from sunlight and moisture. They are in mint condition. And they will stay that way, as i have sprung the money for a set of shockworks coilovers. I'm just working on getting them in at the moment, after rebushing the rear of the car, and while the subframe was out i welded in the GKtech reinforcement bracing as well.  They will get a workout at Ararat King of The Hill in November. I ran 48s on the short course there a few months ago, and i am hoping with new bushes and shocks in the rear i can launch a bit harder. There was a fair bit of axle tramp when i tried too hard off the line. a few of the corners had dips mid way which also made the car feel a bit unsettled, hopefully this will help there too.   
    • Dose Pipe Sutututu
      remote oil cooler hose size, 8,10 or an12?

      By Dose Pipe Sutututu · Posted

      Food for thought, the stock oil filter thread is a 3/4-16 UNF, which has an ID of about 10 to 12mm (according to ChatGPT lol). Now compare than to an 10AN, which has an ID of about 14mm (Raceworks is 14.2mm, Speed flow is 14.27mm).  
    • MBS206
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By MBS206 · Posted

      Yep, totally get that. However hooking in for Generator back up is only a few hundred bucks for the wiring. You could put a couple of those in (for different circuits explicitly) and run a couple of baby generators. Bonus, you can balance them across different circuits, and now have backups in your backup. I'm looking at buying places that won't even have water etc, and I don't mind the idea of getting off the electric grid either, even with everything you've said. This country already has enough power outages that even the mains grid isn't that reliable anymore. I do agree though on spending a bit more to get better gear, and to add some extra redundancy in to the system too.
×
×
  • Create New...