Jump to content
SAU Community

Removing Electric Front Spoiler

debonaire

By debonaire,
in General Maintenance

 Share

Recommended Posts

debonaire Enthusiast

debonaire

Posted
Posted

Hey all,

I will soon be installing a FMIC on my HCR32, necessitating the removal of the active spoiler.

I know people are keen to buy them and put them on their cars, so what has to be sold with it in order to make it work on another car?

I assume you can't swap the whole system as a plug and play unit - because the wiring on the donor car would eventually become untraceable and I would think that the receiving car wouldn't have a place for the switch and motors to plug into anyway.

I am interested to hear from anyone who has sold one of these or anyone has bought one. Have you just sold the spoiler and motors and left it to the buyer to figure out how to operate it, or can it be installed to operate automatically as usual, with the switch as well?

I don't want to be dodgy and flog it to someone who thinks it is going to bolt up and work if it isn't the case...

Link to comment
https://www.sau.com.au/forums/topic/266365-removing-electric-front-spoiler/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      What should I do next to hold the head on

      By Dose Pipe Sutututu · Posted

      Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Dose Pipe Sutututu
      boost source Size Garrett gt28 gen2

      By Dose Pipe Sutututu · Posted

      Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • oHBoy.
      2001 R34DE

      By oHBoy. · Posted

      3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...