Jump to content
SAU Community

Recommended Posts

i just gave my 33 a little fang up the street with a on spot u-turn and wen i got to the end of the street i notice that there was more noise coming from the engine bay... it seems like the fan is working harder or spinning more if that makes any sense... it is normal when the car is idling but if the rpm rises so does the fan noise or the fan rpm.... just sounds like this massive V8 roaring down the street with a huge as fan... not a rathered refined 6cyclinder turbo...

i didn't know wat to search for so yeah sorry guys...

Link to comment
https://www.sau.com.au/forums/topic/26645-fan-problem-help/
Share on other sites

AFAIK, the fan on R33 has a viscous type centre, so the fan should only work when the centre warms up. these centres can die.

As an option (if you have the dollars, I dont know how much a stock fan will cost) buy a twin thermo fan set up from a dismantler, and have that fitted instead. It will need to be adapted, but will give you more power (less load on the crank) and better cooling.

they can be bought from as little as $85 dollars, perhaps less. Go into a radiator shop, they should be able to hook it up with a thermostat to only run when the car gets hot.

Link to comment
https://www.sau.com.au/forums/topic/26645-fan-problem-help/#findComment-562913
Share on other sites

the fan always spins.

the skylines have what they call CLUTCH fans.

it should spin faster with the revs when it gets hot.

It is normal for them to seize up.

You can get a scond hand one from the wreckers for $50 or a brand new one for $150 (these prices are for the clutch part only)

when asking for it, you need to ask for a VL commodore one.

they are identical.

Thermo fans are the other option but it requires some fiddling to get them fitted properly over your radiator and connect up a thermostat and so on.

There are only 4 bolts to take off to remove the the whole fan assembly off your water pump.

then another 4 bolts (I think) to take the fan off the clutch.

Link to comment
https://www.sau.com.au/forums/topic/26645-fan-problem-help/#findComment-563024
Share on other sites

they run but they are sort of passive.

the fan always spins, but when it gets hot, the fluid in the clutch bit makes the plates grap and it turns as fast as the crank does.

normally, when it's hot, you accelerate and you can hear it howl with the revs until about 4000rpm, you hear the fan sound die down.. but it still spins.. just not at the same speed as the crank.

Link to comment
https://www.sau.com.au/forums/topic/26645-fan-problem-help/#findComment-563166
Share on other sites

yeah mine can be turned BUT WITH SEVERE FORCE and only abt 3 cms each way.... so i guess that means that the clutch fan has chucked in ay... damn... there goes another $100 wasted... would've been good to use that to buy a case of beer for u guys... thanks heaps for the help!

Link to comment
https://www.sau.com.au/forums/topic/26645-fan-problem-help/#findComment-564237
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Just wanted to pop in an update on my setup. The CD swap has been great, I love the mazworks housing for the overall simplicity. I ended up sealing my trans tunnel with a thin sheet of aluminum reused some of the holes on the trans tunnel, and laid some window sealing EPS foam around the edges. Works great, really quieted things down and sealed up the car.  As for the power comment. Right now I am also running about 650whp. with the way the bell housing is attached to the face of the transmission I have zero doubts it would be fine, mainly because the input shaft and main shaft bearings are seated into the bell housing adapter. This means the load is NOT on the bolts to maintain the power, rather into he casing of the bell housing; Yes the bolts are doing some work there, but with both shafts locked in zero worries.  End of the day, the Mazworks solution is the easiest and safest. no need to take your trans to a shop to get milled perfectly, it fits with minimal clearancing, and you can use all your existing clutch and flywheel.  Driving wise the CD has been great compared to the big box, I'll probably swap my final drive at some point. The serial 9 shifter is gooooood, my only qualm is how tight it is, it takes a fair bit to get use to, 5th and 6th are a bit eh/hard to find at times, but maybe I need re-adjusting, and I think my clutch master is very tired and needs a rebuild. 
    • If you are keen, have a look at my build thread. Car is for sale for the right money or straight swap for a F80 M3 LCI.
    • Welcome mate.  No point in over thinking it, buying any one of those cars you mentioned is not a smart or logical choice with the availability of many "better" (re price to performance) cars available to you.  The heart wants what the heart wants, buy whatever it leads you too.
    • Hey everyone! Im so grateful to be apart of this community and ill do my best to be apart of this. Firstly, i'm not disclosing my real name due to in real life circumstances surrounding my privacy and public image (sorry lol) Secondly, The only thing personal I am willing to share is that I'm from Sydney and a descendant of one of Sydneys largest mortgage firms. I got gifted my first ever car, a 2022 Porsche Cayenne and I love it to death. Ive been driving it for about 5 or 6 months now and honestly Im so grateful for my parents for gifting me this vehicle. However recently I've been working my ass off to afford my second car (which I need help deciding soooooo community help me out please?). Once decided, im planning to try modify it myself. Recent I've been thinking about getting a Skyline, particularly a 25GT or GT-V, yes I know overrated as hell, but I'm also considering a Chaser which I recently came to love. However my dream is to one day own a 180SX (So hard to find clean versions and im not really into importing).  Lastly before I send this off, I want to apologize if I sound tacky or pretentious. I try not to and want to genuinely learn from everyone and anyone. (Im no expert in this area) Thanks for reading!
    • I've got three stashed away but it's starting to get silly with the prices 
×
×
  • Create New...