Jump to content
SAU Community

Recommended Posts

yo

just wondering if there is any diference in bumper fitment between r33 2 door and 4 door? is so is it much?

reason i ask is cause i am chasing a rear bumper with a bit lower profile. but dont realy want to go for a full aftermarket kit... even a lower lip would work fine, but where the fark would i find one???? seems there are a few options for slightly lower rear bumpers in the 2 door range.

pic attached. u will see what i mean.

peace

matty

post-15190-1240360972_thumb.jpg

Edited by mattysaidso

What toffy said sums it up, about both things...

http://www.autoworx.com.au sell rear 4 door pods that would set off the factory aero look if you wanted keep that "not over the top" look about it that you have going with the factory side skirts. I have not seen any lower lip extensions or rear bars that do not really need bigger skirts and front bar (as in only slightly bigger than stock) anywhere.

They also do Final Konnexion kits which arn't crazy bargo large -

http://www.skylinesaustralia.com/forums/Fi...33-t215946.html

I have a very similar (if not the same) secondhand rear bar sitting in my backyard if anyone is interested in it.

*just noticed autoworx are updating there website and don't currently have the styling stuff listed... Probably easiest to give them a call.

Edited by gunmetalgrey

thanx for the info. :banana:

my next option was a FK kit if i cudnt find anything to lower the lines of my rear bar as it realy shits me. but after lookin at those FK pics again just the rear bar may be an option. and if it looks shit jus buy the rest of the kit...

Blitsbody kits also do R33 4door skirts as thats what i have on my car last i spoke with them they were $150 ea they don't show it in there pictures

http://www.blitsbodykits.com.au/nissan.htm

yeah when i first got the car three years ago i loved it now im way over the VS look

the car is off the road for major repairs and over haul fix up scratches from barbed wire fence :) re-colour new front guards to go on with new reo and front bar and bonnet :) see a pattern

should be good when all finished but im just right @ the beginning of saving for it all Krudd kicked off my savings fund with 1k but ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...