Jump to content
SAU Community

Recommended Posts

hi up for sale i have my 1992 r32 with a rb25 det in it it was a de not to long ago but i decided to replace the whole motor with a rb25det with only 68 000 on it this was a complete stock car until i aded the folowing parts

greedy front mount

tein high adjustable coil overs

blitz 555cc injectors

kkr 430 turbo

3inch dump pipe

2 and half in exhaust (i think)

walbro 550 fuel pump

remaped ecu

extream heavy duty clutch

17 inch rays eng rims

um boost gauge

gizmo electronic boost controler

hks turbo timer

drift gear nob

it also has sun roof

abs which is disconected atm

um ther is also slight rust near sun roof and rear guards

i am chasing around the $14,000 mark neg or open for swaps for a track car worth 5ish and cah my way or a 32gtr and some cash ur way

located in adeladie hills

the car will be avaliable to veiw after this friday the 1st as it is goin to get dyno i will update the power results should be good for 220kw no worries the car still has 2months regon on it any more pics or qustions you can pm me or email me on [email protected] thank you

post-48317-1240637231_thumb.jpg

post-48317-1240637591_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/267021-r-32-with-rb25det/
Share on other sites

yes it is regoed with the 25 and no didn t do upgrade the brakes

ok u have to tell me how you pulled that one off.

when i went through regency to get complienced i had to have rb25det or rb26dett as the rb20det werent big enough. as well as the exhaust emissions tested and all provided to the boys there before registration.

ok u have to tell me how you pulled that one off.

when i went through regency to get complienced i had to have rb25det or rb26dett as the rb20det werent big enough. as well as the exhaust emissions tested and all provided to the boys there before registration.

hey mate if your no interested in buy stop talking s**t in my forum thanks

hey mate if your no interested in buy stop talking s**t in my forum thanks

y such a harsh response??? just a simple question with a simple response would have been nice

some of us would like to know the answer for future reference like me even.

what have u got to hide??? you have told us what it is about so i suspect nothing.

i would like to know also.. i have a street gtr for sale if interested

registered as a rb25de not a rb25det.

hense y its registered with a 25 non turbo. that can be done easy with no dramas.

but would still need full regency.

but if you wanted a track car it would be perfect as hell.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
×
×
  • Create New...