Jump to content
SAU Community

Recommended Posts

I've got my mines chipped ECU for sale which i used in my AUTO - this will suit both manual and auto series 1 r33's, im not sure if it works on series 2.

Specs are:

- Removed rev limiter

- Richer maps to handle hiflow turbo + breathing mods + ~15psi boost. AFR's were at 11.8-12 on boost and ~15.1 AFR cruising.

- Annoying boost cut/r&r removed. I'd log a 5.1v @ 4500rpm and it wouldnt even hesitate to rev.

- would give me 460km to the tank +/-30km depending on how i drove.

Im after $300 + post. by far the BEST bang for your buck mod - you'll notice the power difference instantly even on a standard setup.

I can be contacted via PM or post here.

Pics will be up soon.

Cheers,

Joe

Link to comment
https://www.sau.com.au/forums/topic/267051-mines-ecu-for-r33-gtst/
Share on other sites

not sure on an actual figure mate but i would estimate around 210-215kw when i was running around 10psi, i cant comment on 15psi as i wasnt getting traction at all but it felt awesome. believe me, if you had this in your car you would be confused as to why these things are going for so cheap!

not sure on an actual figure mate but i would estimate around 210-215kw when i was running around 10psi, i cant comment on 15psi as i wasnt getting traction at all but it felt awesome. believe me, if you had this in your car you would be confused as to why these things are going for so cheap!

Yeah mine has 201kw with standard ecu and injectors on 13psi, did yours have bigger injectors with the mines ecu?

And wats the go if u wanna go run 18psi with this ecu, is there much stuffing around?

where ur location?

sydney west

Yeah mine has 201kw with standard ecu and injectors on 13psi, did yours have bigger injectors with the mines ecu?

And wats the go if u wanna go run 18psi with this ecu, is there much stuffing around?

nah mate it had standard injectors. to boost it up to 18psi you wont need much work - just turn up the boost lol.

either way i wouldnt do more than what i said in my first post without getting on a dyno and checking that your AFR's are ok.

im interested. Is it good @ fuel and air flow tuning?

read my first post mate, all the info is there. its not a tuneable computer hence the reason why its so cheap. you just plug it in and off you go.

if you wanted to tune it you'd strap a emanage blue or ultimate to it and you'll be sweet. it will still cost you less than getting a full aftermarket computer if you wanted to go bigger injectors etc etc later on.

I've got my mines chipped ECU for sale which i used in my AUTO - this will suit both manual and auto series 1 r33's, im not sure if it works on series 2.

Specs are:

- Removed rev limiter

- Richer maps to handle hiflow turbo + breathing mods + ~15psi boost. AFR's were at 11.8-12 on boost and ~15.1 AFR cruising.

- Annoying boost cut/r&r removed. I'd log a 5.1v @ 4500rpm and it wouldnt even hesitate to rev.

- would give me 460km to the tank +/-30km depending on how i drove.

Im after $300 + post. by far the BEST bang for your buck mod - you'll notice the power difference instantly even on a standard setup.

I can be contacted via PM or post here.

Pics will be up soon.

Cheers,

Joe

Is it still for sale?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
    • Hello everyone, I am happy to join you.
    • Whereabouts are you, that looks exactly like Akira's old car....
×
×
  • Create New...