Jump to content
SAU Community

Recommended Posts

This car is extremely clean inside and out. Would be the perfect package for someone who does not want to waste a ton of time and money building an ultimate street car out of a r33 gtst.

Item: 1996 series 2, R33 GTS-T Skyline

Location: Gold Coast, QLD

Condition: Exceptional - inside and out

Reason for selling: Now its back from the workshop I have no where to keep it

Odo: 96****

ENGINE

engine rebuilt 3000km ago (just run in and tuned)

balanced crank

pressure tested block

wiseco forged pistons

eagle rods

arp rod bolts

arp head studs

big end oil mod (for better big end lubrication)

blue printed engine

jhh ported head

jhh valve springs

port matched head to manifolds

1.2mm 3 layer cometic headgasket

g ready style plenum

80mm billet throttle body

garett 35/40 with .82 rear housing

42mm External wastegate (plumbed back into the exhast for legality)

stainless steele high mount exhaust manifold (modified for better wastegate flow)

tomie poncams 256/256 8.8mm lift

adjustable exhaust cam gear

os giken twin plate clutch

red line gear box oil

stelth plumb back blow off valve (legal)

custom intercooler piping

600x300x76mm front mount intercooler

oil cooler (mounted behing front bar)

speedflow fittings

braided lines

550cc Nismo Injectors

Splitfire Coil packs (brand new)

N1 OIL PUMP

Genuine Nissan Water Pump

New idle'r bearing

BLITZ SBC ID iii D SPEC Boost Controler

Power FC & hand controller

fuel pressure regulator

bosch 040 fuel pump

gates pro series timing belt

custom 3" turbo back exhaust in stainless steele

3" high flow cat

Z32 air flow meter

K&N pod filter (mounted in front guard for cold air, bolted in for legality)

full s2 mspec body kit with rear pods still intact

iridium spark plugs

blitz oil catch can

95,000 km's on dash now

gearbox has OS 4th and 5th gear set, fitted by Diff Laping at kedron

RDA slotted rotors all round

piston kits on all calipers

paduate race pads all round

dot 5 race fluids in the brake system

reconditioned master cylinder with bored out piston for greater response and feeling

only ever driven with 98ron fuels

Engine built and tuned at 101 motorcafe, springwood. Tuned by Rob.

Made a very safe 408.8HP @ 19PSI ATW. Could easily push another 50-100HP out of this setup.

WHEELS AND SUSPENSION

Rims - 17" volk te37 rims powder coasted silver

Tyres - Kumo 255 rear, 235 front 95% tread (new apart from a few dyno tuning and 500kms)

1" lowered king springs all round ( sits a very legal 150mm from the ground)

bilstein shocks all round

whiteline sway bars front and rear

tomie electric HICAS lock kit with shims

INTERIOR

G-tech on dash apexi turbo timer

blitz exhaust temp gauge

blitz boost gauge

pioneer cd/mp3 head unit

pioneer 6 1/2" splits

power fc hand controller

piller mount for blitz gauges

clarion a class 12" subwoofer in boot (straped down to prevent movement)

phenix gold amplifier

mongoose 3 point battery backup alarm

driver and passenger airbags

EXTRAS

HID headlamp conversion

custom ferrari candy yellow paint job

custom front bar mods to suit intercooler

remote for head unit

1/2 breaker bar and sockets and extensions for the wheels

locking nuts

full set of nissan skyline floor mats ($400)

rear adjustable castor rods

rust free

6months rego

Mobile: 0431430153

Email: aulay AT marvelig DOT com

Price: 22K

Will take some better pictures when the sun comes out, and also post the dyno graph.

post-44294-1241235943_thumb.jpg

post-44294-1241235767_thumb.jpg

post-44294-1241236168_thumb.jpg

post-44294-1241236407_thumb.jpg

The owner of this car is a good mate of mine and ive moved overseas now but i drive a 400HP bluebird. Before he went to town on the engine i had the pleasure to go for a drive in this car and i thought there wouldn't be too many skylines that would impress me after driving my own car. - however this thing is a weapon and i wish i had the money to take it off his hands. I just want to post this up as i know first hand how much effort has gone into this car and stupid amounts of money.

The person who buys it will love it, that im sure of.

Gareth

  • 2 weeks later...
  • 3 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...