Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...
I'm finding I have to check the speedo more often as what feels like 260 can quite easily be closer to 280.

Ha ha, thats funny.

Thats true the car hides the speed so well since its so well balanced and stable at sub sonic speeds, you have to be very careful of where you put your foot down and let off your foot before your eyebrows fly off.

I'm finding I have to check the speedo more often as what feels like 260 can quite easily be closer to 280.

Ha ha, thats funny.

Hi Munro, Thanks for the PM. Yes I'm keen to catch up when u have yours but I cannot reply to your PM because I haven't posted 10 times yet!! Send me an email address via a PM and I'll be in touch.

Cheers

David

  • 1 month later...
Is it just me or has anyone else noticed the calming effect the R35 has on the boy racers.Especially the XRSSHSV ute brigade.I've got a nicely modified 300zx that every time I drive it some young V8 boy wants to race me.Since I've had the R35 the same dudes just want to wave to me or give me the thumbs up and take photos.Not even a hint of mines faster than yours which I'm loving as I do need my licence and in this car there is no stealth mode and I'm finding I have to check the speedo more often as what feels like 260 can quite easily be closer to 280.Got to say though when you do give it a bit I love the sound the turbos make and that's without a Willal Racing mid pipe which will be my first mod.(Martin Donnon from Willal Racing has not payed for this ad for any Willal Racing GTR products that I may or may not of mentioned)(spoken very quickly)but check out his website and have a look at the oil analysis photos.Very scary.I know I'm going on a road trip to SA.That's South not Skylines.As someone that believe it or not has not actually yet driven... say for example ,an F1 car but has driven that other techno marvel the NASCAR in my hurry to get thru a distant green light the other morning whilst being in M mode I did give it a bit of a nail and can only describe the experience as OMYGOD.So in conclusion I propose that in order to eliminate the road toll everyone should be made to drive an R35 and owning an R35 GT-R be made compulsory.Instead of this current KRudd government giving away money to teenage girls to have babies and widescreen TV's make them subsidise R35 GT-R,s so we can at last have a zero road toll.Anyone?

Interesting, but my GT-R seems to make other drivers go crazy though, although i do have people giving me thumbs up but there are still lots of people overtake me just for overtaking me (i was already driving 90 on a 70km road)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...