Jump to content
SAU Community

Recommended Posts

Joel, I have only spun up to forth, that was with about 1/4 to 1/3 throttle, so just accelerating gently, dont want to check 5th as I am scared it will destroy the gear - Pretty scarry when in traffic at around 90-100kmh and the back end is trying to overtake the rest of the car:)

also with 255 goodyear revspecs on the rear and a decent wheel alignment and traction bushes so a reasonably grippy setup.

Hrmmm some of you guys need better quality tyres i think either that or i just need -alot- more power.

My setup is:

Koni front/rear shocks

Struts front/rear

Pineapples (traction setup)

Michelin Preceda 225/50/16 @ 38psi (nitrogen)

~180-200 rwkw (180 on CRD and 200 on UniGroup) so its relatively stock setup i guess.

I can accelerate in any gear on any dry tarmac road and not even get a hint of wheel spin. If I take off from a set of lights like a normal volvo driver (ie, 800rpm) I can use 100% throttle and it just sticks and goes. The -only- way I can get wheelspin is to "drop" the clutch from about 1700rpm and above, even by slipping the clutch their is no loss of traction.

Using your dodgy no name tyres you got from the compliance place simply doesn't cut it. The previous tyres I had on the car (20,000km old) were some Faulken tyre and they would give me non-stop axle tramp in 1st gear, they'd tramline all over the place and good luck slipping the clutch or even dropping the clutch. Tyres make an absolute -massive- difference.

In the wet if i take off like normal with 800rpm (idling level) and then i put my foot flat i'll get axle tramp depending on how wet the road is and how bad the surface is but it doesnt just fry the rear end like some of u are saying.

Benm, even when I was making around 185rwkw, my clutch fried and I upgraded - then I was getting wheelspin in second gear accellerating about half throttle with anything under 1/4 tank of petrol, not using the clutch but roll on. In first it spun the wheels anywhere in that gear if I flattened it.

This was on $420 dollar (each) 255 rubber, ie the revspecs, which are about the best tyre goodyear do rated just below an R series tyre. Maybe your clutch isnt quite gripping the way it should, as I believe that my circumstances are pretty normal for that sort of power? I also have Ohlins coilovers, on about the mid setting, definately not kidney jarring, and pineapples - although I have now included solid cradle bushes as well to help increase the traction.

It also depends on the condition of your diff.

This makes a huge difference. Even if it is slightly starting to get a little loose it will spin up one wheel first then the other will start to spin. Once you loose traction you loose traction.

When I was first making around 164rwkw first gear would really pin you back in the seat and feel like it was really lifting up the car.

At first it would start to spin with axle hop then slowly but surely it stopped axle hopping and has now started to spin up one wheel first then the second wheel causing the car not really to go sideways and not get any traction either.

So yer.. Make sure your diff is nice and tight.

You will know the feeling as when it first starts to go the car will feel like it is slower for some reason but really it is just slightly spinning the one wheel yet still picking up speed and also picking up rev's in turn not quite sounding like it is wheelspinning... Hard to describe.. Hope you know what I mean.

The best test I have found with both the Skyline and the VS Commodores IRS LSD's that have now both gone on me.

Is to in the wet weather, full lock it to the right and try to throw a donut. If it steps out straight away your diff is in good nic. If not and you can hear the inside wheel starting to spin well its on its way.

I can no longer throw a donut and go sideways.. However if I launch it and snap second gear it will snap sideways and sway from side to side through second.

I've got one of those Excedy Organic sports clutches (30% more clamping) and it slips in to third with a hard change. It is around 1 year old. :(

Occasionally on big launches where I slip the clutch to get off the line quickly, when changing in to second it would slip and the rev's would flick straight to red line. In turn I have to back off and re-accellerate again. :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
    • Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
×
×
  • Create New...