Jump to content
SAU Community

Replacement Wheel Studs For Spacer

ColdFusion

By ColdFusion,
in Western Australia

 Share

Recommended Posts

ColdFusion Collaborator

ColdFusion

Posted
Posted (edited)

Hey guys. I've snapped two studs on one of my spacers and I've been trying to find something that will fit, but so far been unsuccessful.

The places I've looked only have the 'Nice Products' range of studs and the closest is just a bit too big. First one on this page http://www.niceproducts.com.au/catalogues/wheel/wheel18.htm is the closest, but the knurl diameter is slightly too big at 12.9mm (the part with the straight lines). Needs to be about 12.2-12.3mm. I bought one to try but the hole is too small for even the first part of the shoulder to go through.

Does anyone here know of a different brand that may fit or even someone who has replaced them before?

If I can't find anything I guess my best bet would be to slightly enlarge the hole so it does fit. I can't see any real problems with doing this as it's only a small amount of material being removed.

Edited by ColdFusion
Link to comment
https://www.sau.com.au/forums/topic/270999-replacement-wheel-studs-for-spacer/
Share on other sites
R DIRTY 3 Grand Master

R DIRTY 3

Posted
Posted

In the past i have taken broken studs to Mr Mag and places like that who can normally match them up.

I believe Coventry's sell studs as well and as long as they are on display at the store you go to you stand a chance of finding a match. If you rely on the parts monkeys at the counter of Coventry's store to match it up for you, it will probably be deemed too hard and they 'wont have anything to match' etc coz they cant be bothered.

  • 5 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • GTSBoy
      Freddy Plenum vs Genuine options RB25

      By GTSBoy · Posted

      My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • Murray_Calavera
      R33 persistent issues. P/steering and lag/misfire

      By Murray_Calavera · Posted

      There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
×
×
  • Create New...