Jump to content
SAU Community

Recommended Posts

A car running 10's isn't exactly a street car. You also need a helmet at the drag strip, and i assume pass scrutineering ? (Not sure don't drag)

A full cage is illegal because there is a cross bar that runs next to your head and you don't wear a helmet on the street so its a possible head injury waiting to happen.

Half cages are legal, have to get the car engineered as a two seater technically but its not a huge problem.

For most defects there are reasons, and there are exceptions to the reason a lot of the time. Which is why you can get the car engineered to allow a car to have mods that are otherwise illegal.

If people decide they don't want to get their car engineered then obviously its gonna be defected.

Not having a go but you have to see it from both sides dude.

  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

i rcn theres more of a chance to get stickered when your driving home late at night with not much other cars around then in a cruise, you gotta be pretty unlucky to be the one to get pulled over out of all the cars on the cruise, just dont be a hero

Hey man i hear ya.

i understand all the reasons behind the legalities of roll cages. Just don't like them as they assume alot. ie the height of the driver, the position of the seat and the type of resraint used. Some mining companies insist on roll cages in light vehicles before they are allowed on to site. Some of these like hilux and Ford courier are smaller inside than a skyline. These vehicles are also required to be road registered. And no a helmet is not required.

My GTR is rego'd as a 2 seater as it was orginally licenced with the half cage. But you'd be surprised at how much stiffer the chassis is with the full cage in. Once i tried it i couldn't go back.

Once E85 comes out in WA, engineering a 10 second, late model car for the street is theory should be possible.

Yeah i see it from both sides but doesn't mean i can't complain about it. :)

i rcn theres more of a chance to get stickered when your driving home late at night with not much other cars around then in a cruise, you gotta be pretty unlucky to be the one to get pulled over out of all the cars on the cruise, just dont be a hero

Dude at 37 i'm one of the oldest owners that hang out on SAUWA. believe me i drive like a nanna on the road. If fact the best thing i ever did was fit a large single. It's so laggy i can drive all day off boost.

This doesn't mean i'm not stereo typed as a hoon because of what i'm driving.

^^ there are a few older boys around than u champ :) and driving equally awesome high hp cars (not talking about myself btw) full roll cage + hitting ur head etc is pretty lame considering technically its illegal to have a gauge mounted in the A pillar for the same reason..

Yeah but if your gauges are far enough down the a pillar, i.e. past the steering wheel, you can get permits for them.

It's like you don't need to have carpet but you have to have a headlining otherwise wires may start to fall down.

deep dish steering wheels are the go, then the problem will be reaching for the indicator switch :blink:

About 90% of rules and regulations might be yarns but there still rules, but getting defected for somethin small when u arent driving like an idiot is unlucky. My advice is cruise, cruise and cruise. If you get defected, think about it then. cos in the end ull end up stressing out more about staying within the rules then actually getting defected. Generally u should keep ur car in good condition anyway tho not because of not getting defected but to keep ur car from stuffing up and to keep u safe. But shet happens sometimes, just enjoy ur car, isnt that why u bought it? If its too hard to not be scared of the police, buy a nice roadworthy volvo and drive with confidence lol

Goodluck mate.

I'll go on 2-3 cruises a week, and maybe see a cop once a month. At most, all they'll do is drive through and make sure everyone is behaving. No one says anything to them unless neccessary.

It's not as bad as everyone makes it out to be, come along to one, run one leg, and see if you enjoy it. I highly doubt your car is as highly modified as Paul's is, so if you get stickered, no big deal.

ive taken my car on four cruises since its been going with no dramas....and thats running high mount turb,external gate,dog box,cage, and f**k all of an exuast and pushing near 500hp atws.......i jst pick when to to be a dick head and have a god look around b4 i open it up.......all so the outside of my car looks stock.........ive had a cop stop behind me at the lights before and with the twin plate its sorta hard to get off the line quietly and smoothly at the same time and still mr plot just cruised by me and didnt even look twice.....plus my car makes no induction noise of any kind till high revs...

Lol you're talking to 'Public Enemy' like he's never been on a cruise before... nawww you cute little kids.

ROFLMAO

I work in Mining, i think i had a maximum of 6 weeks in Perth for the whole of last year. Not a lot of time to cruise, especially when you include time in the workshop.

Gotta a few things i want to finish up on the GTR, ViPec to install and tune, the 19's have recently been painted and need to be refitted, OS giken 5 speed, then i might venture out a bit more often. :D

Public cruises can be an issue due to a minority of hero's showing how cool they are by spinning the wheels at every take off etc....or prooving how tough they are by mouthing off at the police who attend to see whats going on.

We do SAUWA members only cruises....good bunch of guys all driving Skylines (with the odd Stagea, silvia and 350z), no hero's and no problems from the boys in blue.

In fact on a members cruise if that was to happen, the person involved would be told to leave immediately!

the skyline club hasnt held a cruise for a while and even in smaller cruises if a person missbehaves then they are told to leave. try the cruises out of the skyline club they rarely have cop trouble

Well since you asked so nicely.. I guess I could take it out cruising for you while you're away :dry:

But you're paying the fuel bills!

haha thanks for the offer, there are some bloody top blokes on this forum that would do anything to help out a fellow member.

My dad takes it for a spin every now and again. He's pushin 60 and loves it when it comes on boost in 3rd.

Damn straight you can still have fun in a stagea.. I got some tein coilovers and 320awhp, because of the size and weight of the thing it actually has the same white-knuckled fear on a hills run that my 32 does ;)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...