Jump to content
SAU Community

Recommended Posts

Hi guys,

Installed a powerfc and have some problems like some S1 stag's are having, though the pfc should be plug an play (to a degree) with my R34 GTT.

Done some checks and found the following

- Voltage for the throttle motor sensor (pin51) is approx 4.62v.

- Voltage on pin 23 when car is on ignition 0.01 to 0.02 fluctuating,

- Voltage on pin 23 when car is idling is 0.00

- Voltage on pin 37 is 0.00 at ignition and idle

- Voltage on pin 53 is 0.00 at ignition and idle

- Voltage on pin 79 is 0.00 at ignition and idle

I've been told they should be as the following

Pin 23 should be 0.5v approx idling

Pin 37 should be 0.5v approx

Pin 53 should be 4.7v

Pin 79 should be 2v approx

Pin 51 should be 3.4v

symptoms are the following - A/C compressor wont turn on, TCS, SLIP and MIL lights on. powerFC sw sensor check has the THR black background

Im quite lost as to where to look and why so many pins are having no output.

Any idea's where to check?

Link to comment
https://www.sau.com.au/forums/topic/271370-er34-vs-stagea-s1-pinouts/
Share on other sites

Hi guys,

Installed a powerfc and have some problems like some S1 stag's are having, though the pfc should be plug an play (to a degree) with my R34 GTT.

Done some checks and found the following

- Voltage for the throttle motor sensor (pin51) is approx 4.62v.

- Voltage on pin 23 when car is on ignition 0.01 to 0.02 fluctuating,

- Voltage on pin 23 when car is idling is 0.00

- Voltage on pin 37 is 0.00 at ignition and idle

- Voltage on pin 53 is 0.00 at ignition and idle

- Voltage on pin 79 is 0.00 at ignition and idle

I've been told they should be as the following

Pin 23 should be 0.5v approx idling

Pin 37 should be 0.5v approx

Pin 53 should be 4.7v

Pin 79 should be 2v approx

Pin 51 should be 3.4v

symptoms are the following - A/C compressor wont turn on, TCS, SLIP and MIL lights on. powerFC sw sensor check has the THR black background

Im quite lost as to where to look and why so many pins are having no output.

Any idea's where to check?

Series 1 stagea's there are 3 different wiring pinouts/ecu's. I have a series 2 stagea with the neo rb25 and did use a power fc for a while with no problems except for the engine check light which comes on due to no traction control on awd stagea's.

I am a bit unclear to what car/engine combo you have? Is it a stock R34 with the original neo engine, or have you fitted a series 1 stagea engine to it?

Series 1 stagea's there are 3 different wiring pinouts/ecu's. I have a series 2 stagea with the neo rb25 and did use a power fc for a while with no problems except for the engine check light which comes on due to no traction control on awd stagea's.

I am a bit unclear to what car/engine combo you have? Is it a stock R34 with the original neo engine, or have you fitted a series 1 stagea engine to it?

Hey mat,

sorry I should have specified. The car is a R34GTT (ER34) manual with the original neo rb25det. Unfortunately I never had a stock ECU, just an Impul replacement. The impul unit when installed runs fine and no error lights on the dash. a/c TCS can be turned on and off as normal. then switch the loom back to the PFC with the problems as above :)

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...