Jump to content
SAU Community

Recommended Posts

Hi

EARLS braided oil feed line, came in a kit I bought but only needed the water lines. Has the adapter that goes into the turbo (standard GARRETT) so will go into almost any turbo and then the braided line it self with the banjo bolt in the end

The line it self is brand new and comes with two copper washers and banjo bolt (suit S13 SR20DET), copper washers were test fitted but still perfect condition. Specified to suit S13/180SX CA18 & SR20 models but I am almost certain it will suit most Nissan series engines

$110 posted anywhere in Australia

PM or call/SMS 0416 623 381

Located in Melbourne, south eastern suburb s- Dandenong area

Thanks

IMG_0569.jpg

IMG_0570.jpg

IMG_0571.jpg

Link to comment
https://www.sau.com.au/forums/topic/272546-earls-braided-oil-feed-line/
Share on other sites

any proof this an earls line, it looks like a cheap knock off which you can buy the set of three lines with all bolts for about $80...We bought a set for our car, and will never do so again...

sorry mate it just looks cheap, but correct me if i am wrong.

The fittings have EARL's stamped on them, bit hard to tell in the pictures

$100 posted anywhere in Australia

$100 posted anywhere in Australia

$100 posted anywhere in Australia

$100 posted anywhere in Australia

$100 posted anywhere in Australia

$100 posted anywhere in Australia

$90 posted anywhere in Australia

$90 posted anywhere in Australia

$90 posted anywhere in Australia

$90 posted anywhere in Australia

$90 posted anywhere in Australia

$90 posted anywhere in Australia

$90 posted anywhere in Australia

$90 posted anywhere in Australia

$90 posted anywhere in Australia

$90.00 POSTED ANYWHERE IN AUSTRALIA

$90.00 POSTED ANYWHERE IN AUSTRALIA

$90.00 POSTED ANYWHERE IN AUSTRALIA

$90.00 POSTED ANYWHERE IN AUSTRALIA

$90.00 POSTED ANYWHERE IN AUSTRALIA

$90.00 POSTED ANYWHERE IN AUSTRALIA

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...