Jump to content
SAU Community

Recommended Posts

Got a few things for sale, in Adel, west suburbs. all prices negotiable. contact me on 0422976559

6boost low mount steam pipe manifold with 50mm turbosmart pro gate with screamer, suit rb25 1000kms old all for $1700

sard 850cc injectors in standard rail suit rb25, injectors 1000kms old all for $800 also comes with modified injector loom to suit

Nismo fuel reg SOLD

Garrett gt30/82 turbo approx 5000kms old, made 300rwkw on my 25 340rwkw on e85, awesome midrange/topend power n torque

used with 6boost manifold n gate, full boost (23 psi) 4100rpm comes with 3 inch dump $1600

Tomei pon cams suit rb25 s1, 256 dur $800 good cond, used for approx 5000kms

Splitfire coil packs suit s1 rb25/rb20 and rb26, 1000kms old $500

BLITZ number plates, gold lettering on black background. $600 ono

ISC N1 fully adjustable coilovers suit r33 gts-t as new approx 5000kms old $1100

Link to comment
https://www.sau.com.au/forums/topic/273279-r33-rb25-performance-parts-adel/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...