Jump to content
SAU Community

Recommended Posts

Just a quick one...

Since im still looking for that perfect M35 im constantly comming across M's with out some of the features im after... sunroof's, tv, aerokit. But since the sunroofs would be way too much $$$ and i dont like cutting a perfectly good roof up, and an aerokit could be quite pricey considering you would have to blend half the car to get a good finish on the paint (slight perfectionist that i am)... This leads me to thinking if I were to buy an M without the tv sat nav gear what would you need to get it all going?

Questions I have are...

Can you get the tv unit and run other gps through it?

Has anyone pulled one of these out and seen what inputs are in the tv itself?

What are the odds of finding the tv and stuff in oz (thinking IM would ahve to be the go to get this gear)

What would it cost? vs difficulty of install...

Thanks in advance....

Link to comment
https://www.sau.com.au/forums/topic/273532-m35-tvsatnav-setup-can-you-buy-one/
Share on other sites

since the TV unit needs a $400 aftermarket tuner and the Nav doesn't work at all and probably never will (no aussie maps), all you are getting is the fuel consumption stuff basically.

I'd say go for an aftermarket double DIN GPS TV DVD unit to repace the stereo and seriously just buy one with sunroofs and aero.

Mine has the TV etc but in hindsight I would have preferred the aero and I do miss sunroofs. I have had an in dash double din touchscreen allin one nit before and it rocked. The pop screen is cool factor only really, and by the time i've putmy aero kit on and got it painted I would have paid enough for a cusotm pop up screen install i reckon.

I think you would be best getting your M without the TV/Sat Nav option if that is a the one compramise you have to make. The sat Nav will not work in Australia will not work anyway. The TV is an easy fix for about $400.

If you can get one with the single din head unit you can look to choose an aftermarket head unit that has GPS/DVD/TV & ipod input.

That would be my preference.

but if I was to buy the pop up tv itself are you able to use it as an av out option from an after market headunit?

The factory screen is NTSC only so you will need a unit that outputs to NTSC.

I don't know enough about the how the screen plugs into the system so can not answer. Chris Rogers would probably know the answer to this question.

Come along to the meet tomorrow any I am sure you will see a few different solutions.

Cheers

Andy

but if I was to buy the pop up tv itself are you able to use it as an av out option from an after market headunit?

as Andy said it's NTSC as per Japan TV. You can buy the screens off importMstr as they come up all the time but I don't know whether it'd be cost effective. I think you'dprob have to get a fair bit of work done to fit the OEM screen to a car that didn't have it.

You'd certainly be able to buy a cable to get a aftermarket deck to send vid to the screen but the deck would have to output ntsc.

Maybe consider buying a local DVD unit and adding a screen. There's plenty of places around who can do nice custom work to make up a screen and you could get it to deploy from the dash, or even more :).

this is my localguy and there's examples in his gallery of pop up screens:

www.superaudio.com.au

this is in an RX8

rx8screen.png

On the G35 Driver site there is also a couple of threads about installing screens in the OE position. There are companies in the US making a mechanism that will go up and down like the factory.

I was looking at a 7 inch touch screen monitor that from China that looked interesting. Would be good to fit that the OE mechanism and then you can really have some fun.

Cheers

Andy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...