Jump to content
SAU Community

Recommended Posts

Up for sale is my pride and joy. I have had this car for over 2 years and it's time to move on. I have put my blood and sweat into this, and spent over $30k on ithappy.gif

It was an NA Soarer, before the conversion. Since then the following mods have been added since I acquired the car in January 2007

2JZ-GTE Engine

Front Mount Intercooler from Just Jap (brand unknown)

3 inch exhaust which goes into 2*2.5 all the way from the dump pipes backwards (dump pipe not replaced)

K & N pod filter

Body Kit

Tinted Windows

Turbo Timer

Electric Fan with a special controller which you can control to decide what temperature the fan comes on at

4 Gauges (Oil, Boost, Volt and Fuel)

Leather Seats (Group Buy)

New Pioneer Head Unit

HID Head Lights 6000k

18 Inch Lenso Wheels (18*8 Front and 18*9.5 at Back)

These are a couple of the changes it has gone through, just ask if you want to know more.

I also just recently did the 100k service with Paden from Unique Automotive. The service included;

Timing belt

Ignition Coil Plugs

Coolant Flush

Drive Belt

Breather Hoses

Coil Packs

Harmonic Balancer

Timing Belt Tensioner

Water Pump

Fan Clutch

Crank Seal and Cam Seals

Oil and Filter

Fuel Cut Defender

At the moment it is doing around 16psi. I have never boosted this car, and don't intend to. I have been able to reach 16psi because of the FCD. I have also never dynoed this car, because I have always looked after this car with the upmost respect.

It has always being serviced every 5000km since I got the car when it had only done 76,000kms.

I will let the car go for $16,000 without the wheels and $17,000 with the wheels.

post-63549-1244292292_thumb.jpg

post-63549-1244292372_thumb.jpg

post-63549-1244292777_thumb.jpg

post-63549-1244292830_thumb.jpg

post-63549-1244292860_thumb.jpg

post-63549-1244293012_thumb.jpg

post-63549-1244293041_thumb.jpg

post-63549-1244293066_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/273547-soarer-with-a-2jz-gte-engine/
Share on other sites

Cheers guys.

I don't think it's a 10 second car, because I have never taken it to the strip. Like I said, i haven't even dynoed this because I didn't want to push it too hard, more so like a bit of a project for me. Sounds wierd I know!

I did the engine conversion about a year ago on this :D

PRICE DROP. $16000 with the wheels. I will also put in my full sound system which is already installed in the car. It was installed by Lifestyle Car Audio 8 months ago roughly, and cost me around $4000. The system included:

2 * Rockford Fosgate 12 inch P2's

1 * Rockford Fosgate 4 Channel (T400-4)

1 * Rockford Fosgate Mono (T1500-1bd)

6 inch Rockford Fosgate Splits

4 Inch Rockford Fosgate Speakers

All the wiring is done in Rockford Fosgate Wiring. The car is also sound deadened with dynomat.

I would really like to see this car ago, because I want a new car

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • 98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...