Jump to content
SAU Community

Recommended Posts

Hey Guys, have got a few things for sale, will keep adding to the list as i find more stuff

All this stuff to suit RB26DETT, all brand new

ARP Main Studs $225 inc Freight SOLD

ARP rod Bolts $75 inc freight SOLD

ACL Race Series Main bearings Std Size $110 inc Freight

ACL race series Conrod bearings Std Size $55 inc freight SOLD

R33 GTR Crank, brand new $900 plus Freight

All this stuff still in boxes

More stuff

RB26DETT Block with main girdle/cradle: Has been hot tank cleaned, bored out to 87mm, decked a fraction to tidy up the face of the block. has had the mains girdle/cradle fitted and checked the tunnels for out of round/out of spec(Needs welch plugs fitted). $900 plus freight

Venolia 87mm forged pistons to suit RB26DETT, Brand new in box, with Nissan Genuine rings ready for fitting. All ciclips/gudgen pins etc there as well. $1000 inc freight

WILL SELL THE BLOCK, CRANK AND PISTONS AS A PACKAGE FOR $2500 PLUS FREIGHT IF ANY1 IS INTERESTED

STD AFMx3 $20 each SOLD

R32 GTR Crank Angle Sensor $50 1 SOLD, still have 1 more

6x Coil packs $70

ABS Module $120

R32 GTR Steering Rack with tie rod ends $150 SOLD

R32 GTR Clutch slave Cylinder $40

Clutch Master Cylinder $50

Brake Booster and Slave cylinder $150

A/C condensor $50

STD R32 GTR BOV $130

A/C Fan(Fan that sits in front of condensor that also switches on when engine gets too hot) $50

R32 GTR Bonnet Catch $80

Front wheel speed sensors $50 each

Rear Seat(No rips, bit dirty and faded though) $30

Passenger Seat(No Rips) $150

LH Door(White and complete) $250

Bare steering column $20

Glovebox Lid $10

Tailights(White Surrounds) $60 each or $100 pair

STD Fuel Pump $100

Drivers Side Headlight $100

Front propellor shaft $50 SOLD

Starter Motor $50

Another 6 coil packs $70

Coil pack resistor $40 SOLD

Rear window $50

Quarter windows $60 each or $100 pair sold pending payment

Front Crossmember $100

Tailshaft $80 sold

ALL PRICES ARE EXCLUDING FREIGHT

Michael for questions 0438911374

Thanks

More stuff:

ATS Twin plate clutch, half worn, good clutch, HANDLED MY 320kw@WHEELS GTR VERY WELL, EVEN AT 7800RPM LAUNCHES $500

Pair of Garrett 2560-5 turbos, good condition, less than 10000kms old, 1 turbo perfect, other 1 has tiny little bit of shaft play, is rated in HPI magazines top 20 turbos list. Direct bolt on replacement of factory turbos. Come with wastegate actuaters, NO DUMPS though $1200

HKS chipped ECU $50

Veilside Chipped ECU $50

Air filters with the Metal brackets that bolt directly onto AFM $50 pair

STD Turbo dump pipes(pipes that bolt directly onto turbos) $50 pair

Pair of cam/rocker covers(come with the screws that hold it down) $80

Thanks guys, also: still wrecking white R32 GTR, heap of bits sold but still some bits etc on there

i know you dont have one posted up but you wouldn't happen to have a gtr boot and spoiler in white would you?

Also what condition are the coilpacks in??

Thankyou

Aren't the Crankshafts superceded to the R34 crank for some time now? Where'd you find a new R33 crank?

Sorry mate, It must be a R34 crank, when i ordered it from nissan brand new they said that the R32 crank was no longer made, the part number for 32 and 33 were the same, i dont think he checked if the 34 part number was the same as well but knowing nissan it must be the same. Thanks for the knowledge

i know you dont have one posted up but you wouldn't happen to have a gtr boot and spoiler in white would you?

Also what condition are the coilpacks in??

Thankyou

Sorry mate, sold the boot and rear spoiler a few weeks ago.

As far as i know mate, all the coil packs are fine, pulled 1 set out of my 110000km gtr and replaced with the super spark, nothing wrong with the coil packs, just wanted an upgrade and to spend money.

The other set came in a 32 gtr i bought that had been crashed, car started and drove fine, was only running standard boost though

Cheers,

Michael

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...