Jump to content
SAU Community

Recommended Posts

Item: R33 stuff.

radiator support panel ,cut behind strut towers $250ono

cross member (k frame) $150ono

steering rack complete from ti rod to ti rod $180ono

steering rack minus passanger side rack end and ti rod end $100ono

series 1 head lights a pair $300

series 1 rh front bumper blinker $30

dash pads x2 , 1 coverd in genuine white swade $250ono,1 stadard $120ono

series 1 steering wheel $40ono

series 1 front seats $100 a pair

rear seat x2 $50 each

set of 5 aus approved seat belts $150

set of 4 door cards $200 i also have other single door cards $60 each ono

set of 4 inner door/roof molds $100set

hood lining x2 $40ono each

carpot in mint conditon $80ono

kyb suspention $350ono

rear cradle $150ono

rear upper and lower control arms lh side $100ono rh side $100ono

rear hubs complete with brake calipors, lines, hubs, rotors $220ono

front sway bar standard $50ono

rear sway bar standard $50ono

front hubs and rotors $150ono

tail lights and covers x2 and i have 3 colours 2 chose from ,white,marone,red $150 a pair has bolb loom with them as well

x4 power window motors x2 lh and x2 rh $60 each

rear bumper covers and suport bars x2 $100 ono each

series 2 boot wings x2 $120 each in white and 1 in marone

boot lid with shaved boot lock lil ding $80 ono

space saver wheel like new tyre $100ono

set of glass minus front window has tint $250 for the set i paid more just for rear window at a inport wreakers

lots more stuff i will add when i rember or just ask if there is sum think you need i might have it cheers

Location: tweed valley i can deliver to sum places as i work all over the gold coast

Website: here

Item Condition: great

Reason for Selling: not needed

Price and Payment Conditions: as above but make offers

Extra Info: just ask if needed

Pictures: can get but only on dial up atm

Contact Details: here

Link to comment
https://www.sau.com.au/forums/topic/275656-lots-of-r33-parts/
Share on other sites

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

sorry to pll that have pmed me i cant return a pm till my topic cound reachs 10

i do have the a/c pipe skibbo

to thoose who pmed me i pnly have rh side fron lower control arm x2 no lh 1z sorry

the marone boot wing i looked at today has sum clear pealing but yeh i can post at your cost cheers

yeh ill post power window motor for $65 if your keen punisher6942

i should have those triageler plastic bits aidan make offer

isoru yeh still got sway bars ,sorry silbastian dont no if they fit r32

sorry still cant pm ppl so if you want these parts pm me your number and part you want and ill give you a call cheers

sweet as dude ill take one of the drivers side power window motors off ya hands for sure. Text me your bank details and ill transfer the funds when i get your details. My number is 0423819988 and the name is daniel. Ill look forward to hearing from you mate

n/a beast (james) give me your numba and ill give you a call cheers

punisher ill give you a call tomos cheers

sorry ppl i still can pm due to post count no being 10 or sum crap

Edited by DRB25

hey DRB25 still waiting on that phone call or text message with ur banking details champ..... and just want to clarify that the power window motor is in 100% working order???

Hey mate,

Can you give me an address to come and see the car? jus wanna have a look at headlights and some other bits and pieces. The headlights will fit my R33 GTS series 1 aye?

My mobile number is 0402859795.

Cheers mate.

I live in Southport

sorry to pll that have pmed me i cant return a pm till my topic cound reachs 10

i do have the a/c pipe skibbo

to thoose who pmed me i pnly have rh side fron lower control arm x2 no lh 1z sorry

the marone boot wing i looked at today has sum clear pealing but yeh i can post at your cost cheers

hey mate its skibbo here my number is 0415554917 for the big ac hose from fire wall to compressor how much to send to sydney all up cheers mate sydney 2753

Edited by skibbo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
    • OK, now we are ready to get started. You need to remove the air boxes on each side for clearance. The cover is straightforward, undo the clips on the top and lift the front cover out of the rest of the housing. If it is tight you can remove the air filters first. The rear section of the airbox is trickier. On each side you need to remove the Air flow meter wiring which is held to the airbox with a clip; you need to get behind the clip on 2 sides if you want to remove it without breaking it - unclip the harder side and pull on the clip with medium force, then unclip the easier side and it should pop out The airbox is held onto the intake hose with a spring clamp; you need to get a flat bladed screwdriver behind the spring on both sides and pop them outwards. When you have got them in the right unclipped place they will stay there and the airbox slips out pretty freely. Put a rag in the intake to prevent anything getting dropped in there, and also to prevent you seeing that the turbo seal is leaking oil (as they do). Then. The top of the radiator is held by a steel plate, it is secured by 2x10mm and 2x12mm headed bolts . Remove them and remove the plate Also grab the bushings that hold the radiator to the plate on each side so they are not lost!
    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
×
×
  • Create New...